12V Brake & Clutch Pressure Bleeder 12V Brake & Clutch Pressure Bleeder

12V Brake & Clutch Pressure Bleeder

This pressure brake bleeder is designed to be portable, being powered by the vehicle's 12V battery. No shop air required!

Features adjustable output pressure up to a maximum 3.0 bar, with automatic cut-off function when pressure falls below 0.5 bar.

Supplied with premium quality adaptor set made from metal, not plastic.

  • Suitable for both hydraulic brake and clutch systems.
12V Brake & Clutch Pressure Bleeder | Digital

12V Brake & Clutch Pressure Bleeder | Digital

Single handed brake bleeding. Powered by the vehicle's own battery. No shop air required!

  • Bleed pressure is closely controlled up to 3.0 bar - suitable for most vehicles (even those with ABS). Meets European OEM pressure requirements.
  • Auto shut off function when pressure falls below 0.5 bar.

12V Brake & Clutch Pressure Bleeder | Digital

12V Brake & Clutch Pressure Bleeder | Digital

Single handed brake bleeding. Powered by the vehicle's own battery. No shop air required!

  • Bleed pressure is closely controlled up to 3.0 bar - suitable for most vehicles (even those with ABS). Meets European OEM pressure requirements.
  • Auto shut off function when pressure falls below 0.5 bar.
  • Suitable for low viscosity brake fluids.
  • Supplied with European adaptor.

ABS Sensors Reamer Kit ABS Sensors Reamer Kit

ABS Sensors Reamer Kit

A specialised kit for removing dust / dirt / rust when reseating ABS sensors. The kit contains 5 reamers, and one drill to suit most European vehilces.

Designed for use with a 1/4" drv flexible ratchet handle (not included).

  • M10 x 133mm | VAG, Holden
  • M14 x 42.5mm | BMW
  • M15 x 33.5mm | Mercedes, Mazda, Toyota, Ford
  • M18 x 31.5mm | VAG, BMW (E36 | E46)
  • M18 x 42.5mm | VAG, NFZ
  • M8 x 180mm Drill | VW T5

ABS Wheel Speed Sensor Reamer ABS Wheel Speed Sensor Reamer

ABS Wheel Speed Sensor Reamer

A specialised reamer for ABS wheel speed sensors. The fixture hole should be thoroughly cleaned before replacing the sensor.

This 11mm reamer enables precise cleaning of the fixture hole, without expanding the hole diameter / damaging the sensor wheel.

  • 11mm diameter reamer
  • Applications: VAG, including Golf Gen 6 / 7, Audi A3, Skoda Octavia, SEAT Leon

Adaptor | Ford Ranger | 41mm

Adaptor | Ford Ranger | 41mm

SKU: ETWH500BC-48

Adaptor | Ford Ranger | 41mm

This brake bleeder adaptor has been designed to allow pressure brake bleeding on the Ford Ranger from 2012 onwards. This cap screws directly onto the master brake cylinder.

  • Suits Ford Ranger (2012 onwards) vehicles.
  • Nitto style connector fitting
  • Zinc alloy construction
  • 41mm diameter

Adaptor Colorado | Isuzu D-Max (54mm)

Adaptor Colorado | Isuzu D-Max (54mm)

An individual master cylinder adaptor for use with standard pressure brake bleeders, including the ETWH505H. This adaptor is designed to connect to the master cylinder reservoir to allow replacement brake fluid to be pushed through the system.This adaptor suits Colorado / Isuzu D-Max vehicles.

  • Suits Colorado / Isuzu D-Max vehicles.
  • Nitto style connector fitting
  • Zinc alloy construction
  • 54mm diameter

Adaptor Honda | 55mm

Adaptor Honda | 55mm

SKU: ETWH500BC-26

Adaptor Honda | 55mm

An individual master cylinder adaptor for use with standard pressure brake bleeders, including the ETWH505H. This adaptor is designed to connect to the master cylinder reservoir to allow replacement brake fluid to be pushed through the system.This adaptor suits Honda vehicles.

  • Suits Honda vehicles.
  • Nitto style connector fitting
  • Zinc alloy construction
  • 55mm dia

Adaptor Honda | 74mm

Adaptor Honda | 74mm

SKU: ETWH500BC-25

Adaptor Honda | 74mm

An individual master cylinder adaptor for use with standard pressure brake bleeders, including the ETWH505H. This adaptor is designed to connect to the master cylinder reservoir to allow replacement brake fluid to be pushed through the system.This adaptor suits Honda vehicles.

  • Suits Honda vehicles.
  • Nitto style connector fitting
  • Zinc alloy construction
  • 74mm dia

Adaptor Mitsubishi | 34mm

Adaptor Mitsubishi | 34mm

SKU: ETWH500BC-23

Adaptor Mitsubishi | 34mm

An individual master cylinder adaptor for use with standard pressure brake bleeders, including the ETWH505H. This adaptor is designed to connect to the master cylinder reservoir to allow replacement brake fluid to be pushed through the system.This adaptor suits Mitsubishi vehicles.

  • Suits Mitsubishi vehicles.
  • Nitto style connector fitting
  • Zinc alloy construction
  • 34 mm dia

Adaptor Mitsubishi | 35.5mm

Adaptor Mitsubishi | 35.5mm

SKU: ETWH500BC-22

Adaptor Mitsubishi | 35.5mm

An individual master cylinder adaptor for use with standard pressure brake bleeders, including the ETWH505H. This adaptor is designed to connect to the master cylinder reservoir to allow replacement brake fluid to be pushed through the system.This adaptor suits Mitsubishi vehicles.

  • Suits Mitsubishi vehicles.
  • Nitto style connector fitting
  • Zinc alloy construction
  • 35.5mm dia

Adaptor Toyota | 23mm

Adaptor Toyota | 23mm

SKU: ETWH500BC-24

Adaptor Toyota | 23mm

An individual master cylinder adaptor for use with standard pressure brake bleeders, including the ETWH505H. This adaptor is designed to connect to the master cylinder reservoir to allow replacement brake fluid to be pushed through the system.This adaptor suits Toyota vehicles.

  • Suits Toyota vehicles.
  • Nitto style connector fitting
  • Zinc alloy construction
  • 23mm dia

Adaptor Toyota | Lexus

Adaptor Toyota | Lexus

43mm Dia

SKU: ETWH500BC-21

Adaptor Toyota | Lexus

A specialised brake bleeder adaptor, for pressure style brake bleeders. Suits a range of Toyota / Lexus vehicles. Part of the Endeavour Range of brake bleeder tools.

  • Suits Toyota / Lexus vehicles.
  • Nitto style connector fitting
  • 43mm dia

Air Boy Brake Bleeder

Air Boy Brake Bleeder

Single person operation for quickly / cleanly bleeding brakes. Uses shop air for fast brake bleeding.

Includes replenishment bottle for easily refilling reservoir.

  • 1.2 litre cannister
  • Replenishment kit available separately (124143155)

Air Boy Brake Bleeder

Air Boy Brake Bleeder

Replacement black top handle for the Air Boy brake bleeder.

Air Boy Brake Bleeder Clear Hose

Air Boy Brake Bleeder Clear Hose

Replacement clear hose for Air Boy brake bleeders. This hose can be purchased individually, or as part of the brake bleeder refurbishment kit (124143155).

Air Boy Brake Bleeder Nipple

Air Boy Brake Bleeder Nipple

Replacement nipple for the Air Boy brake bleeder. This nipple connects the clear plastic hose (124143203) to the rubber end connector (124143205).

This nipple can be purchased individually, or as part of the brake bleeder refurbishment kit (124143155).

  • For Air Boy brake bleeder (124143100)

Air Boy Brake Bleeder O-Ring | Nitrile

Air Boy Brake Bleeder O-Ring | Nitrile

A replacement o-ring for Air Boy brake bleeders. This o-ring is made from Nitrile and is designed for use with motor oil, not brake fluid,

For brake fluid please refer to SKU# 124143234.

  • For use with motor oil, NOT brake fluid.

Air Boy Brake Bleeder Renewal Kit

Air Boy Brake Bleeder Renewal Kit

Keep your Air Boy brake bleeder in great working condition! All consumable parts are easily replaceable with this renewal kit.

  • O-ring
  • Connector pin
  • Plastic spring
  • Connector hose
  • Nipple
  • End connector

Air Boy Brake Bleeder Rubber End Connector Air Boy Brake Bleeder Rubber End Connector

Air Boy Brake Bleeder Rubber End Connector

Replacement rubber end connector for the Air Boy brake bleeder. This connector connects to the clear plastic hose using a nipple (124143256).

This rubber end connector can be purchased individually, or as part of the 124143155 brake bleeder refurbishment kit.

  • For 124143100 Air Boy brake bleeder

Air Boy Cannister

Air Boy Cannister

1.2 Litres

SKU: 124143200

Air Boy Cannister

A replacement Air Boy cannister. This cannister is interchangeable with any cannister used in the Air Boy range.

This cannister is made from Acetal plastic which is resistant to most chemicals.

  • 1.2 litre capacity

Air Boy Suction Type Brake Bleeder

Air Boy Suction Type Brake Bleeder

SKU: 124143100

$169.00

Air Boy Suction Type Brake Bleeder

Single person operation for quickly / cleanly bleeding brakes. Uses shop air for fast brake bleeding.

  • 1.2 litre cannister
  • Replenishment kit available separately (124143155)

Air Powered Brake Caliper Windback Kit

Air Powered Brake Caliper Windback Kit

Air powered for fast removal of disc calipers. An extensive adaptor kit suits most common vehicles, and includes a 3 pin adaptor required for a range of late model European vehicles, in particular.

  • 23 pcs

Audi 7Pt Ribe QKX8 Caliper Mounting Bolt Socket

Audi 7Pt Ribe QKX8 Caliper Mounting Bolt Socket

A specialised 7 point Ribe socket for removing the radial mounting bolts on Audi RS ceramic brake calipers. These bolts are used on RSQ8 4M ceramic brake calipers on RS6 | RS8 vehicles.

  • 7 Pt Ribe socket
  • 16mm dia x 50mm long
  • 1/2" Sq Drv
  • OEM equiv: 4M8615107C

Bendix Brake Spring Tool

Bendix Brake Spring Tool

For Bendix brakes that have a return spring hooking over a post. The socket end removes springs by rotating the hook post off. The opposite end leverages spring onto post.

  • Equivalent to Bendix S13P

NEW
Boiling Point Digital Brake Fluid Tester Boiling Point Digital Brake Fluid Tester

Boiling Point Digital Brake Fluid Tester

Testing brake fluid boiling point is widely regarded as the most accurate method of testing brake fluid moisture levels.

This compact unit tests DOT3 | DOT4 | DOT5 | DOT5.1.

  • LCD display provides step by step instructions
  • Accurate results displayed in less than sixty seconds.
  • Operates on 12V supply, using vehicle's battery

Brake | Coolant Test Strips Brake | Coolant Test Strips

Brake | Coolant Test Strips

Need a simple / fast / accurate way to test brake fluid & coolant? Are your customers asking for a test report to prove the fluid needs changing? Looking for more service opportunities? Test each car that comes into the workshop...

One double ended strip tests both coolant and brake fluid.

Simply dip a test strip into fluid for 60 seconds.

Patented FASCAR copper testing technology.

  • Double the service opportunities
  • Dual Brake / Coolant test strips
  • Provide customers with a test report

Brake Bleeder Adaptor | 35mm / 3 Lug

Brake Bleeder Adaptor | 35mm / 3 Lug

An individual master cylinder adaptor for use with standard pressure brake bleeders, including the ETWH505H. This adaptor is designed to connect to the master cylinder reservoir to allow replacement brake fluid to be pushed through the system.This adaptor suits Ford Fiesta vehicles.

  • Suits Ford Fiesta MK6 (08-16) vehicles.
  • Nitto style connector fitting
  • 35mm dia
  • 3 lug design

Brake Bleeder Adaptor | 36mm | 3 Lug Brake Bleeder Adaptor | 36mm | 3 Lug

Brake Bleeder Adaptor | 36mm | 3 Lug

An individual master cylinder adaptor for use with standard pressure brake bleeders, including the ETWH505H. This adaptor is designed to connect to the master cylinder reservoir to allow replacement brake fluid to be pushed through the system.This adaptor suits Tesla S / X vehicles.

  • Applications: Holden Colorado (2017-) | Ford Transit (2019-) | Mazda 3 (2015-) | Tesla S (2012-) / X (2015-)
  • Nitto style connector fitting
  • 36mm dia
  • 3 Lug bayonet fitting

Brake Bleeder Adaptor | 4-3/4" x 7"

Brake Bleeder Adaptor | 4-3/4" x 7"

An individual master cylinder adaptor for use with standard pressure brake bleeders, including the ETWH505H. This adaptor is designed to connect to the master cylinder reservoir to allow replacement brake fluid to be pushed through the system.This adaptor suits a range of Chrysler / GM vehicles which are fitted with a tandem reservoir.

  • Suits a range of Chrysler / GM vehicles fitted with a tandem reservoir.
  • Nitto style connector fitting
  • 4-3/4" x 7" (125 x 185mm)

Brake Bleeder Adaptor | 49.5mm | 3 Lug Brake Bleeder Adaptor | 49.5mm | 3 Lug

Brake Bleeder Adaptor | 49.5mm | 3 Lug

An individual master cylinder adaptor for use with standard pressure brake bleeders, including the ETWH505H. This adaptor is designed to connect to the master cylinder reservoir to allow replacement brake fluid to be pushed through the system. This adaptor suits a number of Nissan commercial vehicles.

  • Suits a range of Nissan commercial vehicles and Holden Calais VF (LFX)
  • Nitto style connector fitting
  • 36mm / 49.5mm (1-5/16") OD reservoirs
  • 3 Lug bayonet fitting

Brake Bleeder Adaptor | 50.5mm | 3 Lug

Brake Bleeder Adaptor | 50.5mm | 3 Lug

This master cylinder adaptor suits Hyundai / Kia vehicles, as well as some Nissan vehicles, and the Tesla 3. For use with the ETWH505HA pressure style brake bleeder.

  • Applications: Tesla 3 (2017-) | Hyundai i30 (2012-), Kona (17-23) | Kia Picanto (2011-), Rio (2011-) | Nissan Qashqai (07-10)
  • Nitto style connector fitting
  • 50.5mm ID
  • 3 lug design

Brake Bleeder Adaptor | Nissan

Brake Bleeder Adaptor | Nissan

SKU: ETWH500BC-10

Brake Bleeder Adaptor | Nissan

An individual master cylinder adaptor for use with standard pressure brake bleeders, including the ETWH505H. This adaptor is designed to connect to the master cylinder reservoir to allow replacement brake fluid to be pushed through the system.This adaptor suits a range of Nissan vehicles.

  • Suits a range of Nissan vehicles.
  • Nitto style connector fitting
  • 1-3/8" (34.5mm) ID reservoirs
  • 2 Lug bayonet fitting

Brake Bleeder Adaptor Ford / Mazda Brake Bleeder Adaptor Ford / Mazda

Brake Bleeder Adaptor Ford / Mazda

An individual master cylinder adaptor for use with standard pressure brake bleeders, including the ETWH505H. This adaptor is designed to connect to the master cylinder reservoir to allow replacement brake fluid to be pushed through the system. This adaptor suits Ford / Mazda vehicles.

This adaptor has a double o-ring design that seals to a depth of 14mm.

  • Suits Ford / Mazda vehicles.
  • Nitto style connector fitting
  • Right angle connector
  • Inner cap 36mm dia | Inner point to point 50mm (excluding lugs)
  • 3 lug design