Road Spring
Brand
- Automotive (20)


BMW Differential Bush Tool
A specialised kit for the removal / installation of front and rear differential bushes on BMW vehicles with E38 | E39 chassises.
- Applications: BMW E38 | E39
- OEM bush numbers: 33171090389 | 33171093008 | 33171090089

MacPherson Spring Dumper Extractor
A tool with wide application for removing / installing the shock absorber springs on MacPherson struts.
- Impact / manual wrench operation
- 3 pairs of jaws to fit most MacPherson coil springs
- Small jaw (80-115mm) | Medium (110-150mm) | Large (140-195mm)


MacPherson Strut Spring Compressor
This heavy duty kit has universal application for the removal / installation of springs in MacPherson strut suspensions. This kit is an updated design with a longer working shaft to suit many late model cars / SUVs with longer springs.
This kit is for bench vice mount ONLY.
- 317mm stroke length
- 26,000Nm maximum load


Mercedes Rear Axle Nut Socket
Special six groove profile for removing rear axle nuts on Mercedes Sprinter vehicles.
- 68mm ID
- Six groove profile
- For grooved nut - A970 356 0026
- 1/2" Sq Drv

Mercedes Seal Top Suspension Strut
A special kit designed to remove the seal cap / replace the seal on the air suspension.
- Application: W220

Shock Absorber Ram Bit Socket Set
These pry sockets are designed to extract / replace strut units from the clamp in the hub casting. These sockets are commonly used in European (especially VAG) / Japanese vehicles).
Two piece kit
- 5 x 7mm | 5.5 x 8.2mm
- 1/2" Sq Drv

Strut Nut Socket Set
12 point sockets with cut away profile for servicing strut nuts. These five sockets cover most sizes required for European vehicles.
The cut away design allows access for a hex key to hold the strut while tightening the nut to the specified torque with a torque wrench (hex key is not supplied).
- Sizes: 18 | 19 | 21 | 22 | 24mm
- 1/2" Sq Drv

Track Rod End Socket
After separating the ball joint from the steering knuckle, simply slip over tie rod end and remove. This socket has almost universal application for most cars and some light commercial vehices.
- Inner dia: 49mm | U-opening: 34x18.5mm
- Length: 57.5mm
- 1/2" Sq Drv


VAG Lower Trailing Arm Bush Tool
Hydraulic press tool for removal and installation of the bushes on the front lower control arm, Save hours in labour with this fantastic new design, allowing easy servicing of the common bush failure.


VAG Sub Frame Bush Removal Tool
A specialised kit for VAG vehicles, for removal and installation of the control arm to subframe bush at the front of the front suspension arm.
- Applications: Audi A3 | TT, VW Golf | Jetta | Passat | Tiguan
- Outer dimensions: Piece 1: 65mm | Piece 6: 70mm | Piece 7: 25mm | Piece 9: 60mm

Volvo Front Strut Lower Nut Wrench
A specialised wrench for servicing the front strut lower nut on a wide range of Volvo passenger vehicles.
Designed for use with a torque wrench.
- Applications: XC90 | V70 (00-08) | V70 XC (01-) | XC70 (-07) | S60 | 850 | C70 Coupe (-02) | C70 Conv (-05) | S70 | | S80 (-06) | C70 Coupe (-02)


Volvo Front Suspension Shock Absorber Tool
Specialised tool for separating the sub-frame and shock absorber.
- OEM Equiv: 9997256
- Applications: S80 (99-06) | S60 (01-10) | XC60 (09-) | XC70 (02-07) | V70 (00-07) | XC90

Volvo Truck Rear Shock Absorber Removal Socket
A specialised socket for removing the front wheel shock absorber spring washer on Volvo trucks.
- Pin diameter: 8.73mm
- Circle diameter: 37mm
- 27mm hex drive