90 Degree NRV

90 Degree NRV

Repair Kit

SKU: 190NRV90-08CMR

90 Degree NRV

Repair kit for the 190NRV90-08CM non return valve.

  • Spring
  • Viton pad
  • Biconic valve

Cold Start ValveCold Start ValveCold Start Valve

Cold Start Valves

SKU: ZZ190NA

Cold Start Valves

Cold start valves bleed air from the compressor head during the first few pump revolutions, thus reducing motor staring torque requirements. These valves are especially helpful on oil lubed pumps that may be subject to low temperatures and low starting voltages.

Flat Silencers

Flat Silencers

SKU: ZZ180SLF

Flat Silencers

Working Temperature: From -20oC to 150oC

Body: Brass

Sub Base: Brass

Silencer: Sintered bronze

Flexible Hose

Flexible Hose

1/2" BSP

SKU: 190FLEX

Flexible Hose

Replacement flexible hose for compressors.

  • 330mm long
  • 1/2" BSP female fittings

Bottom Entry Gauges

Gauges | Bottom Entry

These gauges are ideally suited for Compressors, Rotary Pumps and Regulators.

When ordering please order a reading higher than the expected operating conditions, as it may stretch if used continuously on the maximum readout.

If operating around 600-700Pa/85-100PSI, a 1000kPa/1445PSI gauge should be used as a general guide gauges should operate at around 60-70% of their readout. 

Bottom Entry Gauges

Gauges | Bottom Entry

Liquid Filled Gauges provide users with a number of advantages in certain measurement applications. They are ideally suited for use on equipment where excessive vibration and pulsation are encountered, such as pumps, compressors, machine tools etc. The liquid fill minimises the effect of these sever environments, protects the gauge internals and provides continuous lubrication of the mechanism; all adding up to a longer service life. Liquid filling also provides greater protection of gauge internals from corrosive atmospheres.

Liquid Filled Gauges are NOT SUITABLE where oxidising agents are used as:

Oxygen, Chlorine, Nitric Acid and Hydrogen Peroxide are being used.  

Rear Entry Gauges

Gauges | Rear Entry

Dry

SKU: ZZ190R

Gauges | Rear Entry

These gauges are ideally suited for Compressors, Rotary Pumps and Regulators.

When ordering please order a reading higher than the expected operating conditions, as it may stretch if used continuously on the maximum readout.

If operating around 600-700Pa/85-100PSI, a 1000kPa/1445PSI gauge should be used as a general guide gauges should operate at around 60-70% of their readout. 

Rear Entry Gauges

Gauges | Rear Entry

Liquid Filled Gauges provide users with a number of advantages in certain measurement applications. They are ideally suited for use on equipment where excessive vibration and pulsation are encountered, such as pumps, compressors, machine tools etc. The liquid fill minimises the effect of these sever environments, protects the gauge internals and provides continuous lubrication of the mechanism; all adding up to a longer service life. Liquid filling also provides greater protection of gauge internals from corrosive atmospheres.

Liquid Filled Gauges are NOT SUITABLE where oxidising agents are used as:

Oxygen, Chlorine, Nitric Acid and Hydrogen Peroxide are being used.  

Inline Check Valve

Inline Check Valves

SKU: ZZ160CV

Inline Check Valves

Small and Compact

Body is Brass Nickel Plated

Arrow indicates direction of flow

Intake Filters

Intake Filters

Metal

SKU: ZZ190FAM

Intake Filters

99%+ removal efficiency standard: Paper = 2 micron, Polyester = 5 micron

Ability to mount vertically, horizontally

Durable carbon steel construction with powder coated finish or galvanized steel

Filter change out differential: 10” – 15” in. H2O above initial Delta P

Fully drawn weather hood- no wealds to rust or vibrate apart

Interchangeable elements: Polyester, Paper, HEPA

Patented high grade filter element

Temp (continuous): min -15o F (-26 o C) max 220 o F (104 oC)

Tubular silencing design- tube is positioned to maximize attenuation and air flow while minimizing pressure drop

Typical noise attenuation up to 25 dB’s

Intake Filters

Intake Filters

Plastic

SKU: ZZ190FA

Intake Filters

Replacement air intake filter assembly designed to simply screw into the air compressor.

Lever Ball Valves

Lever Ball Valves

Female

SKU: ZZ160SBV

Lever Ball Valves

Suitable for industrial, pneumatic and hydraulic installations.

Ideal for hot/cold water, different oils, compressed air and gas.

Thread: ISO228- DIN259- BS2779

Minimum and maximum working temperature:

  • Air: -15oC, 220oC
  • Water: 0oC, 150oC Without steam
  • Gas: -15oC, 60oC

AGA Lever Ball Valve

Lever Ball Valves

Female

SKU: ZZ160GBV

Lever Ball Valves

Suitable for industrial, pneumatic and hydraulic installations.

Ideal for hot/cold water, different oils, compressed air and gas.

Thread: BS21- DIN 2999- ISO 7/1 Rp parallel Female/Female

Minimum and maximum working temperature:

  • Air: -15oC,220oC
  • Water: 0oC, 150oC Without steam
  • Gas: -15oC, 60oC

Load Genie

Load Genie

A compressor operating in a "start - stop" mode runs more efficiently if pressure trapped in the compressor head and discharge line is released after each pump up cycle.

This Load Genie offers a convenient way to release this trapped pressure. The Load Genie is a combination check and unloader valve. Simply install in the compressor discharge line.

The Load Genie senses air flow when the compressor is running and closes an unloading orifice port. When airflow stops, the Load Genie opens the unloading orifice to release head pressure, and the built in check valve keeps receiver air from leaking back into the discharge line and compressor head.

  • 3/8" PT Female x 3/8" PT Male
  • Flow SCFM: 3 - 12

MDR3 Pressure Switch

MDR3 Pressure Switch

Thermal, 3 pole overload relay for Condor MDR3 pressure switches.

Mini Ball Valves

Mini Ball Valves

Sonsbeek mini ball vales are available with either female connections, or female / male connections. These are high quality ball valves made in Italy, with a metal body / chrome plated finish. These valves are for use with air / water only.

  • Valve body: CW 617N UNI-EN 12164
  • Ball gaskets: PTFE - Teflon
  • Lever: Glass charged nylon
  • Chrome plated body
  • Working pressure: 0 - 220 PSI
  • Working temperature: 0 - 90 degrees C
  • Made in Italy

Mini Ball Valves

Mini Ball Valves

Sonsbeek mini ball vales are available with male / female connections or female only. These are high quality ball valves made in Italy, with a metal body / chrome plated finish. These valves are for use with air / water only.

Non Return Valves

Non Return Valves

90 Degrees

SKU: ZZ190NRV90

Non Return Valves

These non return valves retain air inside the compressor tank. The air compressor pulls in air through the check valve to pressurise the tank. This air creates a backflow pressure against the valve, in turn closing the valve / holding pressure in the tank.

Straight NRVStraight NRVStraight NRVStraight NRVStraight NRVStraight NRVStraight NRV

Non Return Valves

Straight

SKU: ZZ190NRV

Non Return Valves

High quality in tank check valves, with one piece brass bodies, stainless steel springs and glass filled fluoropolymer poppets. Eight discharge holes ensure quiet operation.

Condor MDR2 Pressure SwitchCondor MDR2 Pressure Switch

Pressure Switches | Condor

Genuine Condor single phase pressure switches. Available in different sizes to suit a range of different thermal overload ratings.

MDR3 Pressure SwitchCondor MDR3 Pressure SwitchCondor MDR3 Pressure SwitchCondor MDR3 Pressure Switch

Pressure Switches | Condor

Genuine Condor 3 phase pressure switches. Available in different sizes to suit a range of different thermal overload ratings.

NEMA Pressure Switches

Pressure Switches | NEMA

Genuine, made in Italy, Nema single phase pressure switches.

York Check Valves

York Check Valves

SKU: ZZ160YCV

York Check Valves

Suitable for industrial, pneumatic and hydraulic installations.

Ideal for hot/cold water, different oils, compressed air and gas.

Thread: BS21- DIN 2999- ISO 7/1 Rp parallel Female/Female

Minimum and maximum working temperature:

  • Air: -20oC, 110oC
  • Water: 0oC, 90oC
  • Gas: -20oC, 60oC