Camshaft setting bars for locking the camshaft when servicing the camshaft timing chain on select Audi / VW vehicles. Commonly used in VW VR6 / W8 / W12 engines.

• OEM equiv: T10068A
• Use in conjunction with ET1105A-4

Specialised socket for Bosch rotary / distributor type diesel pump tamperproof screws, commonly used on VAG systems.

• 7mm size: EDC pump cover socket (1996 - 2003) | Bosch OEM Equiv: 0986612605
• 12.6mm size: VE diesel pump socket | Bosch OEM Equiv: 098661750

Specialised sockets for disassembling Bosch fuel pumps. This kit contains five tamperproof sockets for bolts commonly found on these fuel pumps.

• 7mm: EDC pump cover socket (96-03) OEM 0986612605
• 12.4mm: VP37 pump
• 12.6mm: VE Diesel Pump Socket OEM 098661750
• 14.4mm: Cover screw 28.1mm: Dial gauge cover

Oil pump locking tool for 2.0L, 2.2L, 2.4L, 3.2L diesel engines and 2.3L Duratec petrol engines.

Allows the oil pump to be removed / replaced in the same position (to ensure that the oil pump is not operating with excessive side loads).

• Mondeo | Ranger | Transit (2.0 / 2.2 / 2.4 / 3.2 TDCi / TDDi / Di Duratorq)
• OEM Equiv: 303-705 | 303-1093 (PSA 0198H)

This timing tool kit is designed for 2.0L | 2.4L Ford Duratorq engines (including timing pump removal / installation). Suits engines built from 2002 - 2010.

The kit includes a chain tensioner, fuel pump cover removal tool, fuel pump sprocket locking tool, and camshaft / crankshaft sprocket alignment pins.

• Applications: Ford Transit VH VJ VM | Jaguar X-Type X400
• Engine codes: BG | D2FA | FXFA | H9FA | H9FB
• OEM Equiv: 303-249 | 303-675 | 303-679A | 303-682 | 303-698 | 303-1151

A specialised cylinder head rebuilt kit designed to allow the camshafts to be correctly fitted into the cylinder head on Porsche / VAG common rail engines.

The set contains a jig, various camshaft support fixtures, gear tooth alignment clamps and locking devices.

• OEM Equiv: T40094 | T40095 | T40096
• Applications: VAG 1.6L | 2.0L | 2.7L | 3.0L | 4.0L | 4.2L diesel CR engines | Porsche 3.0 TDi
• For timing servicing on 2.7L - 4.2L engines, also refer ET1622.

An updated comprehensive timing kit for late model belt driven petrol VAG engines. This kit includes an updated camshaft locking tool for post 2013 engines with Cylinder On Demand (COD).

For the camshaft holding kit refer ET1872A.

• Engines: 1.0L 3 Cyl | 1.2L TFSI | 1.4L TFSI / TSI
• Designed for petrol TSI / TFSI engines (direct injection, belt- or chain-driven) in the EA111 | EA211 engine families. Not compatible with diesel engines (e.g., TDI) or older indirect injection petrol engines
• Primarily covers VAG models from ~2007 to 2018, with emphasis on 2010-2016 for most applications. Later models with EA211 evolutions (post-2018) may require different tools

Comprehensive timing tool set for latest generation belt driven petrol TSI engines used across the VAG range. Includes support for 1.4L CoD (cylinder on demand) engines.

• OEM Equiv: T10340 | T10476 | T10477 | T10494 | T10499 | T10504

An upgraded timing tool kit for VAG 1.2L | 1.4L | 1.6L TFSi / FSi engines.

• Applications: Audi A1, Skoda Fabia | Octavia | Roomster, VW Beetle | Golf | Jetta | Polo | Touran
• A DTI gauge (ET1101) is required, but not included in this kit, as most workshops will already have one.

A specialised tool for fitting / removing PTFE radial crankshaft seals in the control unit without damaging them.

• Engine: 1.2L FSI: CBZA | CBZB | CBZC
• Applications: Golf / Golf Plus (2009>) | Polo (2010>)
• OEM Equiv: T10417/1, T10417

A comprehensive kit for locking the camshaft / crank in their timed position. This allows for the servicing of the camshaft drive chain. Includes guide pins required for aligning the supercharger (on those engines to which it is fitted).

• Engine codes: CBZA | CBZB
• Applications: Audi A1 | VW Beetle, Caddy, Golf, Passat | Skoda Fabia, Rapid, Roomster, Yeti.

These two tools are required for setting the camshaft / tensioner on 1.4L | 1.6L petrol engines found in various VAG vehicles from 1999 - 2014.

This kit is suitable for use with replacement cam belt kits: Contitech CT957K1, Gates K025565XS, INA 530 0089 10.

This flywheel locking tool is suitable for the VAG 1.4L TSi chain driven petrol engine.

An essential tool for installing the rear mail oil seal with the integrated sender wheel.

• OEM Equiv: T10134 (for OE seal # 03L 103 171A)
• Compatible with diesel engines in the EA188 (1.9L / 2.0L TDI PD) and EA189 (1.6L / 2.0L TDI CR) families

Specialised locking tool kit for 5th generation diesel Blue Motion engines. Set includes crankshaft locking tools for both styles of VAG sprockets.

• For Gen 5 common rail diesels (Blue Motion)
• Applications include 1.6L | 2.0L TDi engines fitted to Audi A3 | A4 | A5 | A6 | Q5, VW Golf | Passat | Tiguan
• OEM equiv: T20102 (3359) | T10050 |T10051 | T10052 | T10100 | T10255 | T10264 | T10265 | T40098

These two tools are required for setting the camshaft / tensioner on 1.6L | 2.0L petrol engines found in various VAG vehicles from 1997 - 2011.

This kit is suitable for use with replacement cam belt kit: Contitech CT908K1, Gates K015489XS, INA 530 0171 10.

A specialised timing tool kit for locking camshafts / crankshafts in position on post 2013 1.6L | 2.0L diesel engines. The kit also includes pins for timing the gears in the cylinder head.

• Applications: VAG 1.6L | 2.0L TDI engines including VW Golf VI / VII, Audi A3 | A4 | A5 | A6 | Q5 | TT
• OE equiv: T10264 | T10265 | T10490 | T10051 | T10060A | T10492 | 3359

A specialised timing tool kit is for 1.8L | 2.0L TSi / TFSi 4v engines. This kit includes a TDC indicator. The TDC indicator needs to be used in conjunction with a DTI gauge. The DTI gauge (ET1101) is not included in the kit, but is available separately.

This kit is designed to allow removal / replacement of the timing chain and camshaft sprockets. The kit includes special camshaft pulley locking blocks for late model Gen 3 TSi / TFSi engines.

On third-generation EA888 1.8 and 2.0L 4V TFSI engines, the ET0037A is required to remove the damper pulley when servicing the timing chain.

Quickly / safely install rear crankshaft seal flanges on 1.8L | 2.0L TSI | TFSI chain drive engines.

• Applications: Audi A4 (08-16), VW: Golf (15-17) | GTI (08-17) | Jetta (12-17) | Passat (14-17) | Tiguan (09-17)
• Engines: CCZ
• Gearbox size
• 86mm dia
• OEM equiv: T20097

Timing chain tension lever designed to be used with the ET0900. Broad range of applications on 1.8L | 2.0L TSFI engines.

For pretensioning the timing chain and unlocking the chain tensioner. Attach to the cylinder head, and then push back the chain tensioning rail. Allows for replacement of timing chain without needing to remove the front cover.

• EA888 Gen III engines (but can also be used with Gen 1 & II)
• Engine codes: 1.8L | CDAA, CDHB, CJEB, 2.0L | CCZA | CCZB | CCZD | CDNB | CESA | CPSA
• OEM Equiv: T40243
• Designed to be used in conjunction with timing kit ET0900

A specialised kit for removing the camshaft sprocket from the taper on the camshaft on Pumpe Duse / common rail diesels. Includes a counter hold tool for loosening / tightening the camshaft hub bolt.

• Engines: 1.9L | 2.0L TDI
• OEM Equiv: T10051 | T10052

Auxiliary belt tensioner wrench for removing / installing the poly V-belt on 1.4L 4 Cyl TSi / TSi BlueMotion engines (turbo & supercharged).

• OEM Equiv: T10447

A comprehensive timing tool kit for belt tensioning a wide range of 1.8L | 2.0L petrol FSi / TFSi engines. The kit includes locking pins, camshaft alignment tool and tensioner wrench.

This kit includes necessary tools for servicing the chain in head and establishing correct valve / camshaft timing.

Applications for Audi A3 | A4 | A6 | S3 | TT

OEM Equivalents & Engine Codes:

• DA0379-23: VAG 3366, VAG T20018, VAG T20044
• ET1020A: BMW 11 2 300, Holden KM 813, Land Rover LRT 12-108
• ET1084-1: VAG T10092
• ET1084-3: VAG T10252
• ET1220B: VAG T10020
• ET2207-3: VAG T10060/A, VAG T40098, VAG T20167, VAG 3204
• TT4001: VAG T40011
• AXW | AXX | BGB | BHZ | BLR | BLX | BLY | BMB | BPJ
• BUL | BVY | BWA | BWE | BYD | BZC | CDLB | CDLC | CDLG

A specialised kit for replacing timing chains on Porsche | VAG petrol engines. This kit suits a wide range of 6 | 8 cylinder engines.

• Applications: VW Bora | Eos | Golf Mk IV | Golf Mk V | Passat | Phaeton | Touareg | Sharan | Transporter T4 | Transporter T5, Audi A3 | A8 | Q7 | S8 | TT, Porsche Cayenne.
• Engines: 2.8L, 3.2L, 3.6L, 4.0L, with 6 & 8 cylinder petrol engines

Adjustable design allows it to work on any sprockets of suitable size. Maximum spoke width - odd numbers 27mm, even numbers 17mm. Forcing screw with 17mm hex head. Body width: 133mm.

• Suits 5 or 6 spoke camshaft pulleys
• OEM Equiv: T40001

Locking tensioning pin for ribbed V belts.

• Engine codes: AAH | AFC | AAN | APB | AHA | ATQ | AVK | ART | AWN | BBD | BWA
• OEM Equiv: T10060/A

For servicing the camshaft adjuster securing bolt on 2.0L TFSi engines. M10 Polydrive (short version) - longer version T10070.

Do NOT use a standard Torx socket when removing the bolt on the camshaft sprocket.

• M10 Polydrive (6 splines)
• 54mm length
• OEM Equiv: T40080
• 1/2" Sq Drv

A set of three assembly camshaft tools for removing camshaft control valves before chain removal, on 4 Cyl chain drive petrol engines.

• Application: 1.8L | 2.0L 4 Cyl chain drive petrol engines
• OEM Equiv: T10352 | T10352/1 | T10352/2
• 3/8" Sq Drv

This tool locks the camshaft in position on 1.2L FSi / TFSi petrol engines found across the VAG range from 2009 - 2017.

Do not use this item as a holding tool when loosening / tightening the camshaft sprocket!

• Engine codes: CBZA | CBZB
• OEM Equiv: T10414

Better alignment with 2 ground shoulder screws & facilitates timing adjustment with the vacuum pump & cam cover still in place. The ground screws slide the setting bracket easily into the camshaft slot with the addition of the knob for precise alignment.

• OEM Equiv: 3418 | T10098 | T20038

Setting plate for valve timing on VAG chain drive VR6 engines. Also for FORD Galaxy 2.8L (VR6)

• Size: 175mm wide x 95mm long.

A specialised kit for removing / installing the camshafts on VAG petrol engines. Please refer to ET0900 for the relevant timing tool kit.

• Engines: 1.8L | 2.0L TFSI Turbocharged 4V
• OEM Equiv: T40191 | T40196

Rotate and hold the camshaft on 1.8L | 2.0L TFSI Gen III petrol engines. Use with ET0281 timing kit, and ET9716 crankshaft pulley holding tool.

• Engine: 4 Cyl 1.8L | 2.0L 4V TFSI (Gen III)
• 3/8" Sq Drv
• OEM Equiv: T40266

A specialised wrench to hold the pulley while loosening / tightening the pulley fixing bolt. This tool is recommended by the manufacturer to set the No. 1 cylinder at TDC. Covers engines from 2006 onwards.

• Applications: 1.8L | 2.0L TFSi / TSi petrol engines
• OEM Equiv: T10355

A specialised tool for ensuring the correct alignment of the main seal house crankshaft sensor on 1.4L | 1.6L 16 valve engines fitted to specific VAG vehicles.

• OEM Equiv: T10017

A 4 piece kit designed specifically for Volkswagen and Audi technicians tackling direct ignition engine repairs. This essential set ensures safe, efficient removal of stubborn ignition coils without risking damage to delicate components.

Primarily compatible with EA111 | EA888 series petrol engines (1.2L-3.2L) with direct injection, found in VAG vehicles from ~2000-2010. Also compatible with 1.2L / 1.4L TSI (e.g., CBZB, CAXA) in later models like Golf MK6 | Audi A1.

• Two square prong for final output stage
• Single sided square for coils with power stage
• Wide shallow square for coils with final output