This set is designed to refill radiator coolant by creating a vacuum in the cooling system, allowing coolant to be replaced without introducing air pockets. Supplied with a cone shaped adaptor to suit a variety of radiator filler necks.

• Lift vehicle / drain old coolant / replace drain plug
• Hang vacuum unit under bonnet
• Connect coolant hose and drain hose to vacuum pump (check that all valves are closed)
• Put coolant hose in coolant / make sure hose is always submerged
• Turn on vacuum switch and vacuum valve. Turn off once vacuum is created
• Turn on coolant valve. Coolant will flow into the radiator

This timing kit has been designed for late model Ford 2.0L EcoBlue engines in the Ford Transit (2016 >) which have the belt in oil design whereby the drive belt is located inside the oiled area on the engine.

• Application: Ford Transit (YN | YO)
• Engine codes: YMF6 | YNF6 (2016 onwards)
• OEM Equiv: 303-1637 | 303-1643 | 303-1650 | 23-019

A specialised tool for removing the vibration damper pulley on 2.0L EcoBlue engines fitted in the Ford Ranger | Kuga | Transit, from 2019. Allows for safe removal without damaging the bonded rubber section. Ensure that thrust screws are suitably greased, in accordance with manufacturer specifications.

• OEM Equiv: 303-1657
• Application: Ford Ranger | Transit | Transit Custom
• Engine: 2.0L EcoBlue | YN2S

A specialised diesel injector puller designed to allow injectors on Ford 2.0L EcoBlue engines to be removed in our piece, so that they can be retrofitted.

• Applications: Ford 2.0L EcoBlue engines
• OEM Equiv: 303-1706

A specialised kit that assists with the extraction of very tight fitting injector nozzles, utilising a special pull spindle. Contains a 17T hydraulic ram, with 15mm stroke. Height retracted 89mm | extended 104mm.

This kit is designed to be used with a bridge, and injector pullers. These are available separately.

• M14 x 1.5 pitch Pulling Spindle 240mm long.
• M14 x 1.5 pitch Pulling Spindle 315mm long.
• M17 x 1.0 pitch Pulling Spindle 240mm long.
• M17 x 1.0 pitch Pulling Spindle 315mm long.
• M18 x 1.5 pitch Pulling Spindle 315mm long.
• M25 x 1.0 pitch Pulling Spindle 240mm long.

A specialised kit for removing BMW diesel injectors in vehicles with M47 | M57 engines, without having to remove the cylinder head.

The special extraction bridge and pull spindle allows for quick / safe injector removal.

To avoid the risk of impurities entering the combustion chamber during the cleaning process, we strongly suggest the use of a compressed air adaptor.

• Engine codes: M47TU | M57 | M57TU
• Spindle 16 (one side M17) for mounting in the injector
• 29mm socket for disassembling the electric unit
• Internal 6 Pt wrench for removing the injector needle

A specialised kit for removing seized diesel injectors from VAG TDI engines, along with BMW N47 | N57 engines. The removers have a special two jaw design to fix the injector and pull out with a sllide hammer.

• Engine codes: BMW N47 | N57, VAG ALH | ALU | 1Z
• OEM Equiv: T10055 | T10402 | T10415 | T10163 | T40055

A specialised tool for late model BMW N55 petrol engines to safely / quickly install / remove the fuel injectors. For earlier N55 engines (before July 2013) please refer to ET1539A.

• Application: BMW 3.0L (2008 - 2016)
• Engine: N55 (from July 2013 onwards) - up to engine # 14407684
• OEM equiv: 130270 (13 0 270)

Kit consists of a slide hammer with adaptors to assist the removal of stubborn Bosch and Lucas diesel injectors.

• Adaptors: M8 P0.75 (male) | M12 P1.5 (Bosch) | M14 x P 1.5 (Volvo / Scania)
• Slide hammer thread: M12 | 175mm length (without adaptors).

Specialised kit for demounting stuck injectors (mainly Bosch) without removing the cylinder head. Wide coverage on 1.3L - 2.2L diesel engines.