For new generation COMPACT impact wrenches.

All ESSENTIAL sizes, especially 15mm for Commodore harmonic balancers.

• 6 Point
• Chrome moly impact sockets
• Sizes: 13mm - 19mm, 21mm, 22mm, 24mm
• 1/2" Sq Drv

This kit is designed to remove high security BMW wheel lock bolts with spinning rings, where the bolt cannot be removed because the key is missing, or the bolt is rounded etc.

A faster solution than grinding / drilling, which is also more likely to result in damage to the wheel.

This kit allows the wheel lock bolt to be removed in a few minutes. A real timing saving tool!

• Slide hammer: M16 x 1.5

Professional one person brake and clutch bleeding. Simply connect the adaptor to the master cylinder, fill the container with brake fluid, and pump. No external power source is required.

• 2.8 litre capacity
• Supplied with 44mm adaptor (ETWH500BC-06) that suits many European (and BYD) vehicles
• Other adaptors available separately

An essential set of popular sizes of brake caliper sockets used on Audi / VW / Porsche vehicles.

These sockets are specialised 7 Point & 10 Point sockets with a range of different diameters (which are measured from the inside rim of the sockets).

• 9mm | 10 Point - Audi Q7 / Touareg / Porsche
• 11.5mm | 10 Point - Porsche
• 14mm | 7 Point - Audi Q7
• 15mm | 10 Point - Audi Q7 / Porsche
• 20mm | 10 Point - Porsche Cayenne
• 22mm | 7 Point - Audi S5

This tool is used to check for proper pin-fit and tension on US, European and Asian automotive electrical female terminals. This tool covers Japanese and Korean built vehicles including, Toyota, Honda, Mitsubishi, Mazda, Nissan, Subaru, Suzuki, Isuzu, Kia and Hyundai vehicles. This tool also covers US joint venture vehicles including Ford / Mazda, GM / Toyota, Ford / Nissan, and GM / Suzuki.

The tool is precision manufactured in the US. The tool has looped wires that are colour coded and the colour code chart is located on the packaging. The tool meets all RoHS requirements for all of the components and the finished product.

A must-have tool to properly diagnose electrical and electronic concerns on all common makes and models.

• Colour coded
• Made in USA
• Check socket fit condition

Updated version with 'sharp tip' tip for better grip. Designed for disconnecting automotive electrical connectors while avoiding damaging locking tabs.

• Spring loaded, for easy use
• Ergonomic molded handles for comfortable use
• Sharp tip
• 185mm overall length

Disconnect electrical connectors quickly, safely, and without damage with the Endeavour ET7070 Electrical Disconnect Pliers. Designed specifically for modern automotive electrical systems, these specialist pliers make it easy to release stubborn connector locking tabs and separate wiring harness connectors that can be difficult to access by hand. The updated serrated jaw design provides positive engagement with connector locks, allowing connectors to be released cleanly and efficiently.

• Spring loaded, for easy use
• Ergonomic molded handles for comfortable use
• Serrated tip to better grip connectors
• 215mm overall length

This tool is used to check for proper pin-fit and tension on US, European and Asian automotive electrical female terminals. This tool covers Japanese and Korean built vehicles including, Toyota, Honda, Mitsubishi, Mazda, Nissan, Subaru, Suzuki, Isuzu, Kia and Hyundai vehicles. This tool also covers US joint venture vehicles including Ford / Mazda, GM / Toyota, Ford / Nissan, and GM / Suzuki.

The tool is precision manufactured in the US. The tool has looped wires that are colour coded and the colour code chart is located on the packaging. The tool meets all RoHS requirements for all of the components and the finished product.

A must-have tool to properly diagnose electrical and electronic concerns on all common makes and models.

• Colour coded
• Made in USA
• Check socket fit condition

The ET8040 disconnect kit is designed to assist with releasing electronic connectors on Knorr Bremse EBS modules. This kit comprises 3 tools for separating 2, 4, 6 & 12 pole electrical connectors on the trailer module, as well as a tool for loosening the bayonet nut on the power supply connection.

• Ideal for tight working areas on HGV trailers
• Manufactured from steel with vinyl dipped handles for improved comfort / grip

Specialised electrical disconnect pliers for push tab fittings commonly used on Fuel Injectors, Ignition Coils, Mass Airflow Sensors etc.

• Long length swivel jaws provide access to deep seated / hard to reach connectors
• Applications include Fiat | Mercedes | VAG

An essential set of terminal release tools for cleaning / replacing / removing terminals from the plastic connectors on most wiring connectors without damaging them.

• 23 pce kit
• Please see download link for information on individual disconect tools
• Soft grip handles with number identification