Perfect for connecting to fuel injectors, MAP and TPS sensors, as well as any weather pack seal type connectors. The modular design is compatible with any industry-standard, 4mm plug whether shrouded or not. All probes are supplied in a protective plastic tube.

• 4 colours | 0.7mm (0.028") OD back probe pins
• Made in UK quality
• 1000V CAT III 20A

These reels hold 6 metres of highly flexible double skinned silicone cable suitable for use with standard multimeters.

• 1000V CATIII double / reinforced insulation | 20 Amp current rating
• 4mm Straight plug / 4mm Right angle plug
• Fully compliant to IEC 61010-031:2015

The Power Probe 4 is a multi-use Circuit Tester with built-in diagnostic power.

This tool simplifies the testing of fuse boxes, verifies correct operation of motors, lights, relays, sensors, wires, communications circuits and computer drivers. The large LCD colour display makes viewing live test information and mode selection simplified in even direct sunlight or complete darkness.

• Supplies Power and Ground
• Digital voltmeter with Min/Max voltage capturing
• 20 ft power lead
• Tests for bad grounds / short circuits
• Powered by vehicle battery
• Gold plated brass probe tip
• Directed LED head lamps to illuminate test area
• Ohmeter / Frequency
• Pulse width (+tive & -tive)

Additional diagnostic modes:

• Petrol fuel injection tester
• PCM / ECM driver tester
• Signal tracer (use with ECT3000)

• 1000V CAT III 20A
• 30 cm cable

Test battery charge / health for all 12V auto batteries and alternator / crank systems for 12V / 24V batteries, including new stop start batteries.

Print test results using the built in printer.

• Tests all main battery standards
• Max load voltage tests for 12V / 24V
• Short circuit / reverse polarity protection

Monitor battery status on all 12V automotive batteries. Wireless communication (up to 50m) by RF frequency. No need for cables / mobile phone app!

• Solar powered with internal battery (or charge via USB)
• Battery status (SOC / SOH / Voltage) etc. Plus check vehicle starting / charging systems.
• Easy dashboard mount / audible alerts.

This pressure brake bleeder is designed to be portable, being powered by the vehicle's 12V battery. No shop air required!

Features adjustable output pressure up to a maximum 3.0 bar, with automatic cut-off function when pressure falls below 0.5 bar.

Supplied with premium quality adaptor set made from metal, not plastic.

• Suitable for both hydraulic brake and clutch systems.

Single handed brake bleeding. Powered by the vehicle's own battery. No shop air required!

• Bleed pressure is closely controlled up to 3.0 bar - suitable for most vehicles (even those with ABS). Meets European OEM pressure requirements.
• Auto shut off function when pressure falls below 0.5 bar.

A professional quality automotive battery tester for testing both 12V lithium ion and lead acid batteries. This tester uses conductance technology; a passive testing methodology which does not discharge / drain the battery. This analyser also checks the alternator's charging and starter's cranking condition.

• Tests all 12V lithium ion / lead acid batteries for cars / motor cycles.
• Print function via PC printer
• Testing range: Lithium ion 20- 1000CCA | Lead acid 20 - 2000CCA

This petrol engine timing light is designed for professional use. Featuring multiple measurement modes and a rotating barrel for better aim at the timing market and LCD viewing angle.

• Tachometer: 249 to 9,990 RPM (± 1% Accuracy)
• Dwell: 0¡ to 180¡ / 2 - 12 cylinders (±1% Accuracy)
• Voltage: 10 - 16V DC (± 1% Accuracy)
• Advance Degrees (2 / 4 cycle DIS & Conventional): 0¡ to 90¡ ( ± 0.5¡ Accuracy)