The ET2031B Universal Line Kit is a versatile, multi function diagnostic set designed for fast, secure connection to vehicle wiring during general engine testing and circuit evaluation. It enables quick probing, signal access, and component activation across a wide range of automotive systems, making it an essential tool for efficient fault finding and reliable electrical diagnostics.

This kit comes with a bonus multimeter - offering a comprehensive diagnostic solution.

• Dual-Function LED Testers - these two-way LED circuit testers allow for quick identification of power and ground signals, making fault-finding faster and more intuitive.
• Black & Red Multimeter Connector Leads - ensuring reliable connectivity for a wide range of diagnostic tasks.
• Round Terminal Adapters (Male & Female) to Banana Plug - male and female round terminal adapters connect seamlessly to standard banana plugs; ideal for interfacing with OEM wiring and connectors.
• Flat Blade Terminal Adapters (Male & Female) to Banana Plug - Includes flat blade terminal adapters for compatibility with common automotive spade connectors, improving versatility during testing.
• Variable Resistors with Banana Terminals - adjustable resistors allow technicians to simulate loads, test sensor circuits, and diagnose voltage dependent faults with confidence.
• Needle Style Piercing Probes - designed for clean, precise back-probing without damaging insulation; perfect for modern fine gauge wiring.
• Heavy Duty Alligator Clips - these rugged clips provide strong, secure connections to battery posts, chassis grounds, or test points, ensuring stable readings during diagnostic work.

A comprehensive kit designed for extracting inner bearings, bearing outer rings and bushings.

This kit includes 10 different sized adapters (from 6mm to 58mm diameter), two mechanical pullers, and a slide hammer attachment.

• Puller sizes: 6-10mm | 8-12mm | 10-14mm | 12-16mm | 14-19mm | 18-23mm | 20-30mm | 28-40mm | 35-46mm | 45-58mm

This clamp adaptor is a transducer which will allow your oscilloscope, motor tester or multimeter to measure electrical current up to 600 amperes, both types AC or DC, with a frequency response up to 400 Hz.

When measuring current with this clamp adapter, there is no need to break into the circuit or disturb the isolation as the opening jaws simply clamp around the current carrying conductor. No electrical contact is required.

• 30mm jaw opening
• 0 - 600A range (AC / DC)
• 0-600mV output (AC / DC)
• Supplied with 4mm banana plug type connectors. A separate BNC to 4mm adaptor may be required for some applications.

A specialised current clamp to allow your oscilloscope, multimeter to measure electrical current from 10mA up to 60A - both AC / DC - with a frequency response up to 20kHz.

This current clamp adaptor is ideal for displaying current waveforms for fuel injectors, fuel pumps, ignition coil circuits, and testing the solenoid valve for electronic diesel fuel injection control (EDC) systems.

The small measuring jaws allow the adaptor to be used in tight spaces.

• 4mm banana plug connectors
• Two calibration settings: 10mA - 20A AC / DC range & 20A - 60A AC / DC range
• 9mm max jaw opening
• 9V DC battery supplied with unit

Adds a Pressure Pulse sensor for engine health testing, 2x AC/DC clamp meters for current testing and doubles the ignition testing components to fully utilise both channels on the scope.

AutoSim allows a mechanic to simulate the replacement of a sensor.

Simulating output signals of most automotive sensors, AutoSim picks up service issues where a scan tool's diagnosis ends. Sensors tell the on-board computer when something is wrong. AutoSim helps determine if the cause is a faulty sensor, wiring or the ECU.

The product is mainly used for wiring tests. This is because the device can simulate the voltages and check the live data readings on the scan tool to confirm the wiring. You can simulate most sensors from ABS to O2 sensors. Eliminates need to replace non-defective sensors; by the time you have changed a couple of un-needed sensors the device has paid for itself!

• Voltage simulation range: 0.1V ~ 12V
• Frequency simulation range: 0.1Hz ~ 10KHz
• Trigger pulse output: up to 0.15 amperes maximum
• Output amplitude: 0.2V to 12V output amplitude can be selected at each mode

Ditex heavy duty oscilloscope automotive test leads are made with silicon insulated leads and nickel plated gripping surfaces for optimum electrical performance. The oscilloscope test leads are available with BNC plugs to connect to your automotive diagnostic equipment.

• 150 Strands of Copper Wire
• Super Flexible Silicone Cover, 18 AWG (0.75 mm2)
• Jacket special silicone rubber (non-sticking treatment) with 2.3mm outer diameter of silicon jacket
• 2m (7 feet) total length (1.5m coaxial cable and 0.5m silicon wire)
• Long cable life assured by the soft molded strain reliefs at all stress points
• Wide operating temperature range: -65 ¡C to +150 ¡C
• Alligator type clip ground lead, and an active test lead with high quality 4 mm banana plug