CarScope Pressure Transducer Kit

SKU: ET0084K

CarScope


In the modern age of diagnostic repair being able to monitor the engine dynamic pressure and vacuum enables you to find serious mechanical faults. Test cylinder or whole engine to find leaks, blocked ports, valve performance in minutes.

This kit contains our new pressure sensor with the following key features - 100 µS extremely fast response time; 500 psi / 35 bar input pressure range; ±0.3% pressure non linearity; 3x pressure overload.

Connects directly to almost any oscilloscope via BNC connector.

Suits common spark plug sizes.

  • M10 x 1.0
  • M14 x 1.25 (Short)
  • M14 x 1.25 (Deep)

SKU ET0084K
Barcode # 9321280416314
Brand CarScope
Product weight 1.4000kg
Shipping weight 1.750000kg

12 Months


More from this category


CarScope #1 Cylinder Pick Up Clamp

CarScope #1 Cylinder Pick Up Clamp

This inductive clamp is designed to clip onto the spark plug wire to cylinder one to get the trigger signal that is used to identify the correct cylinder number of each ignition voltage signal.

CarScope AC / DC Current Clamp

CarScope AC / DC Current Clamp

A specialised current clamp to allow your oscilloscope, multimeter to measure electrical current from 10mA up to 60A - both AC / DC - with a frequency response up to 20kHz.

This current clamp adaptor is ideal for displaying current waveforms for fuel injectors, fuel pumps, ignition coil circuits, and testing the solenoid valve for electronic diesel fuel injection control (EDC) systems.

The small measuring jaws allow the adaptor to be used in tight spaces.

  • 4mm banana plug connectors
  • Two calibration settings: 10mA - 20A AC / DC range & 20A - 60A AC / DC range
  • 9mm max jaw opening
  • 9V DC battery supplied with unit

CarScope AC / DC Current Clamp

CarScope AC / DC Current Clamp

This clamp adaptor is a transducer which will allow your oscilloscope, motor tester or multimeter to measure electrical current up to 600 amperes, both types AC or DC, with a frequency response up to 400 Hz.

When measuring current with this clamp adapter, there is no need to break into the circuit or disturb the isolation as the opening jaws simply clamp around the current carrying conductor. No electrical contact is required.

  • 30mm jaw opening
  • 0 - 600A range (AC / DC)
  • 0-600mV output (AC / DC)
  • Supplied with 4mm banana plug type connectors. A separate BNC to 4mm adaptor may be required for some applications.

CarScope Advanced Accessory Kit

CarScope Advanced Accessory Kit

Adds a Pressure Pulse sensor for engine health testing, 2x AC/DC clamp meters for current testing and doubles the ignition testing components to fully utilise both channels on the scope.

Carscope Automotive Sensor Simulator

Carscope Automotive Sensor Simulator

AutoSim allows a mechanic to simulate the replacement of a sensor.

Simulating output signals of most automotive sensors, AutoSim picks up service issues where a scan tool's diagnosis ends. Sensors tell the on-board computer when something is wrong. AutoSim helps determine if the cause is a faulty sensor, wiring or the ECU.

The product is mainly used for wiring tests. This is because the device can simulate the voltages and check the live data readings on the scan tool to confirm the wiring. You can simulate most sensors from ABS to O2 sensors. Eliminates need to replace non-defective sensors; by the time you have changed a couple of un-needed sensors the device has paid for itself!

  • Voltage simulation range: 0.1V ~ 12V
  • Frequency simulation range: 0.1Hz ~ 10KHz
  • Trigger pulse output: up to 0.15 amperes maximum
  • Output amplitude: 0.2V to 12V output amplitude can be selected at each mode