The SmokeMan ET4396 is a compact, high-performance pressure brake designed for fast, clean, and reliable brake fluid exchange. This unit streamlines brake bleeding, allowing it to be undertaken by one person - no need for a second technician. Powered by the vehicle's own battery - no shop air required!

• Bleed pressure is closely controlled up to 3.0 bar - suitable for most vehicles (even those with ABS). Meets European OEM pressure requirements.
• Auto shut off function when pressure falls below 0.5 bar.
• Includes premium adaptor kit

The ET7850 is a compact, handheld diagnostic tool that combines a 100MHz dual-channel oscilloscope, a 20,000-count multimeter, and a comprehensive automotive diagnostic suite - all in one rugged device, along with an extensive accessories kit. Designed for field technicians, mechanics, and engineers, it delivers precision, portability, and versatility for real-time fault detection and waveform analysis.

A key feature for automotive professionals is a built-in waveform library for ignition systems, sensors, injectors, and bus protocols. This supports diagnostics for independent & distributorless ignition systems, crankshaft & camshaft sensors (inductive & Hall effect), ABS, MAP, lambda, knock, and coolant sensors,CAN, LIN, K-line, FlexRay bus systems, common rail diesel injector analysis etc. Plus the ability to import (and compare) known good waveforms!

• 2 channel oscilloscope
• 100MHz Bandwidth
• 500MSa/s Sampling Rate
• Type C rechargeable battery

This inductive clamp is designed to clip onto the spark plug wire to cylinder one to get the trigger signal that is used to identify the correct cylinder number of each ignition voltage signal.

This clamp adaptor is a transducer which will allow your oscilloscope, motor tester or multimeter to measure electrical current up to 600 amperes, both types AC or DC, with a frequency response up to 400 Hz.

When measuring current with this clamp adapter, there is no need to break into the circuit or disturb the isolation as the opening jaws simply clamp around the current carrying conductor. No electrical contact is required.

• 30mm jaw opening
• 0 - 600A range (AC / DC)
• 0-600mV output (AC / DC)
• Supplied with 4mm banana plug type connectors. A separate BNC to 4mm adaptor may be required for some applications.

A specialised current clamp to allow your oscilloscope, multimeter to measure electrical current from 10mA up to 60A - both AC / DC - with a frequency response up to 20kHz.

This current clamp adaptor is ideal for displaying current waveforms for fuel injectors, fuel pumps, ignition coil circuits, and testing the solenoid valve for electronic diesel fuel injection control (EDC) systems.

The small measuring jaws allow the adaptor to be used in tight spaces.

• 4mm banana plug connectors
• Two calibration settings: 10mA - 20A AC / DC range & 20A - 60A AC / DC range
• 9mm max jaw opening
• 9V DC battery supplied with unit

Adds a Pressure Pulse sensor for engine health testing, 2x AC/DC clamp meters for current testing and doubles the ignition testing components to fully utilise both channels on the scope.

Ditex heavy duty oscilloscope automotive test leads are made with silicon insulated leads and nickel plated gripping surfaces for optimum electrical performance. The oscilloscope test leads are available with BNC plugs to connect to your automotive diagnostic equipment.

• 150 Strands of Copper Wire
• Super Flexible Silicone Cover, 18 AWG (0.75 mm2)
• Jacket special silicone rubber (non-sticking treatment) with 2.3mm outer diameter of silicon jacket
• 2m (7 feet) total length (1.5m coaxial cable and 0.5m silicon wire)
• Long cable life assured by the soft molded strain reliefs at all stress points
• Wide operating temperature range: -65 ¡C to +150 ¡C
• Alligator type clip ground lead, and an active test lead with high quality 4 mm banana plug