New Products

Nylon test cap to be connected to recovery tank filler necks.

• Applications: MG vehicles (including EVs)

Nylon test cap for connection to recovery tank filler necks. Suits early model VAG vehicles.

• Applications: Audi | SEAT | Skoda | VW
• M57 x 3.0 thread

A heavy duty oil filter wrench designed with wide steel band to offer maximum torque, while avoiding crushing filters.

Universal application including agricultural, construction, heavy commercial vehicles etc.

• 110 - 128mm capacity
• Band width: 40mm
• 1/2" Sq Drv

A heavy duty oil filter wrench designed with wide steel band to offer maximum torque, while avoiding crushing filters.

Universal application including agricultural, construction, heavy commercial vehicles etc.

• 96 - 115mm capacity
• Band width: 40mm
• 1/2" Sq Drv

Nylon test cap for connection to recovery tank filler necks.

• M50 x 2.5
• Applications: Chevrolet Aveo | Ford | Land Rover | Mercedes | Saab

A short series single hex oxygen sensor socket for the removal / installation of Oxygen / Lambda sensors. Designed with a slot in the side to allow it to be fitted over the wiring harness.

• Applications: Jeep Grand Cherokee 3.0L V6 diesel (from 2014) | Dodge RAM 1500 3.0L V6 Diesel (from 2014)
• Overall length - 70mm
• 24 mm diameter | 6Pt
• 1/2" Sq Drv (or can also be driven with a 30mm wrench

This Duramax Flywheel Holder is designed for 6.6L Duramax engines with Allison automatic transmissions. This tool locks the flywheel in place, making it easier to remove the harmonic balancer without needing to remove the starter. It includes a 36mm 12-point socket with a 3/4-inch square drive, allowing for smooth removal and reinstallation of the harmonic balancer bolt.

• Applications: Chevy Silverado 2500 | 3500 | 4500 | 5500

A specialised suspension tool for removing Tesla Model 3 / Y rear steering knuckle bushings.

This time saving tool allows for removal / installation of bushing / ball joints without detaching the knuckle. Kit includes high strength steep press cups and threaded rods for stable and precise operation.

• Suits OE rear knuckles: 1044411-00-G / 1044411-00-F / 1288416-00-A
• OE equiv: GB0-0360 / 1188412-01-E

A professional quality socket for removing / installing BPW axle hub caps. Ideal for trailer axles in the 13 - 14 ton class. Use as a pre-service tool before applying roller axle nut sockets (ET1171C).

• Applications: BPW 13-14T class
• 95mm dia (Oval profile)
• 3/4" Sq Drv

A professional tool for removing / installing wheel bearing cups on trucks / trailers / other commercial vehicles with axle capacities from 11 - 50 Ton.

The tool is adjustable to fit most large vehicle applications. Precision engineered jaws grip the diameter of the cup, reducing the risk of damaging the bearing face.

Saves time & energy! One tool covers a broad diameter range - replacing individual bearing plates.

• Extends from 3-5/8" - 6-1/2" (92 - 165mm)
• Applications include: 453-X | BR563 | BR3720 | BR3920 | HM212011

A heavy duty socket designed for servicing BPW 13 - 14 ton trailer roller axle nuts.

Refer ET1050A-6 for removal of the axle lid.

• Bore diameter: 85mm
• Inner width: 52.5mm
• 3/4" Sq Drv

A heavy duty solution to swiftly and reliably prime diesel fuel systems. Capable of holding around 3 litres of diesel, it is operated by a high pressure hand pump.

• Applications: Cummins DD13 | DD15, Detroit MBE900 | MBE 4000 | S60
• OEM equiv: J-47912

A heavy duty oil filter wrench designed with wide steel band to offer maximum torque, while avoiding crushing filters.

Universal application including agricultural, construction, heavy commercial vehicles etc.

• 125 - 143mm capacity
• Band width: 40mm
• 1/2" Sq Drv

The Power Probe PP3EZKIT is an all-in-one automotive diagnostic kit designed to streamline fault-finding and component testing. It allows you to power up and activate components directly, trace wiring and circuit faults with precision, and expand troubleshooting capability using advanced probe tips and accessories. Ideal for fast, accurate electrical diagnostics across modern vehicle systems.

• Quickly Locate Short and Open Circuits - pinpoint wiring faults with speed and precision, drastically reducing diagnostic time.
• Complete Diagnostic Kit - Includes both the PP3EZ Power Probe for activating and testing circuits and the ECT3000 Circuit Tracer for fault finding in hard to reach wiring, providing a comprehensive all in one testing solution.
• Activate Components with Power or Ground - apply power or ground directly to components, enabling instant functional checks without back probing or jumper wires.
• Includes Tip Adapters - two essential adapters for current measurement (PPAMP) and PWM signal testing (PPPWM), expanding diagnostic capability for modern automotive systems.
   

The ET3142 is a professional-grade breakout box designed for advanced in-vehicle diagnostics and bench-top ECU testing on both 12V and 24V systems. It exposes every OBDII pin for full signal access, monitors live circuit voltages with true-RMS accuracy, and includes selectable CAN termination for controlled network testing. Its secure, high-speed interface allows safe integration of scopes, scan tools, and other diagnostic equipment, making it an essential tool for precise fault-finding, signal analysis, and ECU development work.

• Real Time VRMS Voltage Monitoring on All OBDII Pins - the integrated LCD displays true RMS voltage across all 16 pins, delivering accurate diagnostics even on fluctuating or noisy circuits. Green background highlights active dynamic signals, while immediate alerts help identify power or ground issues on critical pins (4, 5, and 16).
• Built In CAN Termination for Bench & ECU Testing - an onboard 120 ohm CAN termination switch is ideal for situations where termination is missing such as single ECU or small bench networks. This helps improve signal integrity, reduce line reflections, and stabilise communication during advanced diagnostic work.
• Intelligent Voltage Protection & Audible Alarm System - reverse polarity protection, automatic alarms for over voltage and under voltage conditions, and support for currents up to 2A, ensures that both the vehicle and diagnostic tools stay protected during testing.

Professional grade diamond-coated fuse terminal cleaning set purpose built to rejuvenate electrical connectivity and enhance circuit reliability.

• Precision blades in 8mm | 10.4mm | 14mm widths.
• 0.5mm blade thickness
• 30mm blade length (fitted into a 142mm overall tool body)

Radiator test caps for major Chinese car makes, including BYD, Chery, Geely, GWM, Haval, LDV, and MG. Made with high quality and sturdy nylon materials.

Caps connect with a pressure pump (not included - ET1039-1) for leak tests. Or connect to a vacuum tool (not included - ET1039-PURGE) for coolant refill.

A radiator test cap for late model GWM / Haval vehicles. Designed to connect to the recovery tank filler neck.

• M63 4.0
• Suitable for the cooling system recovery tank on Haval Big Dog, Cool Dog, Jolion, Raptor, and GWM Tank 300, Tank 500, Ora EV

A specialised cleaning gun for helping to remove bacteria from the air conditioning system. The gun injects cleaning fluid directly into the air conditioner evaporator.

The cleaning detergent leaves a protective layer in the air conditioning system that keeps it clean and at the same time secures a clean odour in the car. As quality and functionality always matters to Air Boy, our AC Cleaner is both easy to use and produced in impact-resistant quality materials that makes the tool long lasting.

Use the 900 mm extension probe for deep evaporator cleaning, or easily switch to the included spray nozzle for standard cleaning gun functionality.

• Remove bacteria / odours
• Bonus Spray Nozzle - simply screw on.

A front crankshaft seal extractor designed for Iveco / Fiat 3.0L diesel engines. Screw into the old seal, and remover in accordance with OEM instructions, without damaging the casing.

Refer to ET1005IV for oil seal installation tool.

• Applications: Iveco Daily | Fiat Ducato | Fuso 4P10 (Euro 5)
• OEM equiv: 99340059 | MH063989

A specialised 3 point type socket used for adjusting automatic transmission gears.

• Applications: Fuso / Benz 5th Gen lift trucks
• Fuso OEM equiv: MH062979

This Hub Cap Impact Socket is a specialist tool designed for use with BPW ECO axle systems. Engineered for precision and durability, this socket ensures safe and efficient removal and installation of hub caps during axle maintenance and servicing.

• Axle types: H.. / K.. / N.. 6.5 - 12 t ECO H.. / K.. ECOPlus H.. / K.. / N.. ECO Plus 3
• 111mm dia (oval)
• 1" Sq Drv
• OE equiv: 03.364.29.03.0

A heavy-duty 8 Pt socket designed for professional maintenance of large commercial vehicles. Engineered specifically for Scania 10-wheel cabs, York haulage trucks, and FUSO 10.5T vehicles, this socket is ideal for removing and installing the third axle nut with precision and reliability.

• 95mm dia | 8 Pt
• 3/4" Sq Drv
• Applications: Scania trailer axle | York haulage trucks | Fuso 10.5T trucks | BPW axle systems
• OEM equiv: Fuso MC870996

A professional-grade axle nut socket designed specifically for servicing BPW 12 tons axles. Built for heavy-duty use, this tool is essential for removing and installing roller bearing axle nuts on BPW 12-ton axles, ensuring safe and efficient maintenance.

• Designed for use with a torque wrench
• 80mm x 50mm
• 3/4" Sq Drv
• OEM equiv: 03.266.47.03.0

The ET8040 disconnect kit is designed to assist with releasing electronic connectors on Knorr Bremse EBS modules. This kit comprises 3 tools for separating 2, 4, 6 & 12 pole electrical connectors on the trailer module, as well as a tool for loosening the bayonet nut on the power supply connection.

• Ideal for tight working areas on HGV trailers
• Manufactured from steel with vinyl dipped handles for improved comfort / grip

A special 8 Rib wrench suitable for removing the fuel filter on new Canter Euro 4 trucks, as well as servicing oil mist separator on Fuso 380 series trucks over 17 ton.

• Applications: Canter Euro 4 4M50 (3.5T | 6.7T | 6.9T), Fuso 380 6M70 (over 17T)
• OE equiv: PA66-GF30 | MH062301
• 109mm x 8 Ribs
• 1/2" Sq Drv

This kit is designed for repairing differential, gearbox, sump plug threads. Simply tap the damaged thread slightly oversize (oversize tap included), and then fit a new drain plug and washer.

This kit is ideal for use on M12 x P1.50 sumps where the thread has been stripped or worn.

• Designed to repair threads on M12 x P1.50 sumps
• Applications: BMW | Mercedes
• Includes tap plus 6 drain plugs / copper washers.

A specialised socket for removing / installing rear hub nuts on select LDV vehicles. This nut needs to be removed to service handbrake shoes, half shafts and rear brake discs.

Do not use with impact tools.

• Applications: Maxus V90 | Deliver 9 (2019 Onwards)
• 2 pin socket | 88mm OD
• 3/4" Sq Drv

The BMW ET6198A Locking Kit is a precision engineered kit designed for servicing the oil pump sprocket on BMW's N55 engine.

This kit locks the oil pump sprocket in place during disassembly and reassembly, ensuring precise timing and safe handling.

• Application: BMW N55
• OEM equiv: 2303793 (83302303793)

The ET4177 is an impact grade socket designed specifically for Iveco Daily rear hubs. Plus other applications requiring a 65mm diameter socket.

• 65mm thin wall impact socket
• 12 Point
• 3/4" Sq Drv

The ET1353C is a comprehensive disc brake service kit engineered specifically for Knorr-Bremse brake systems, trusted across European truck fleets. Designed for professional technicians, this kit streamlines maintenance and ensures precision servicing of high-performance disc brakes.

• Applications include most European trucks. including Scania / Volvo.
• Disc brakes: ADDB22X | SK7 | SN6 | SN7

A professional impact socket designed for servicing the shackle pins / leaf spring on current model Mack / Volvo trucks, and Superliner ETC.

• Pin dia: 8.9mm
• 1/2" Sq Drv
• OEM equiv: 9996791 (TG15103), for use with OEM pins: 1589024 | 15890247 | 1614230 | 16142309

This Volvo Tool is a specialised shock absorber spring compressor designed for Volvo FM and FH 500P / 540P trucks. Engineered for precision and efficiency, this tool is essential for safely removing and replacing cabin shock absorber springs, particularly during maintenance or when addressing leaks. Its robust construction ensures durability, while its compatibility with the ET1246A enhances versatility. Ideal for professional mechanics, this tool simplifies complex repairs, making it a must-have for European truck maintenance.

• Applications: Volvo 500P | 540P | FH | FM
• OEM equiv: 9998276

A specialised tool designed to quickly and safely release the gearbox input speed sensor (G182) connector. Suits various VAG models.

• Applications: 6 Speed dual clutch 02E | 7 Speed dual clutch 0BH | 0BT
• OEM Equiv: T10465

An essential tool for avoiding damage when installing the rear crankshaft oil seal on Hino E13C trucks.

• Applications: Hino E13C trucks - 390 / 420 / 446 HP (700)
• Genuine oil seal: BZ5222F

A specialised kit for removing / installing spring eye bushes on European trucks.

Many European truck brands have designed special spring eye bushes, as a consequence requiring special tools to be used for their servicing. This master kit suits a range of MAN / Renault / Volvo trucks. Optional adaptors available for DAF vehicles.

Supplied with a 12T hydraulic ram. This unit requires a hydraulic pump to operate (which is not supplied).

• Applications: MAN (410 / 414 / 460) | Renault (340 / 450 / 460) | Volvo (FM12)