A specialised kit for setting the balance shafts on common BMW (4 & 6 cylinder) | Mini | Citroen | Peugeot petrol engine vehicles.

• Engine codes: N42 | N45 | N46 | N46T | N52
• Engine codes: BMW 1.6 (N40 / N45 / N45T, B16, B16A, B16AC) 1.8 / 2.0 (N42 / N46 / N46T) 2.0 / 3.0 (N51 / N52 / N52-Component / N53 / N54), PSA: 1.4 / 1.6 16V (EP3 / EP6 / EP6DT / EP6DTS), Mini 1.4 / 1.6 (N12 / N14)

A master timing kit for BMW 2.5L | 3.0L petrol engines. This kit is designed to hold the camshafts / crankshafts when working on the timing chain / engine timing.

• Engine codes: N51 | N52 | N52K | N53 | N54 | N55

Holds vibration damper when loosening and tightening center bolt. Suits most BMW 4 Cyl & 6 Cyl engines (01-).

• Applications: N12 | N14 | N42 | N45 | N46 | N52 | N54
• Supplied with pulley bolts
• OEM Equiv: 11 9 280

A specialised kit for safely removing / installing the front crankshaft oil seal on 4 Cyl & 6 Cyl BMW engines.

This updated kit is suitable for a wide range of BMW N series engines.

• Applications: N42 | N45 | N46 | N52 | N52K | N53 | N54 | N55
• OEM Equiv: 11 0 370, 11 9 220 & 11 9 230

Used to grip & remove vibration damper & retaining bolts. Use with ET1121A-5 puller.

• Engine codes: M52 | M52TU | M54
• OEM Equiv: 11 8 190

For locating upper and lower bearing strip when installing exhaust camshaft. Includes 6 thrust blocks and valve spring compressor.

Use in conjunction with ET1188B and ET1556A (to remove eccentric shaft / intermediate shaft).

A versatile / time saving kit to press down the exhaust camshaft to allow for easy removal / installation. Also holds the bearing strips in place when fitting the intake camshaft.

• Engine codes: B58 | N52 | N54 | N55

Flywheel locking pin suitable for 2.0L 4 Cyl diesel and 3.0L 6 Cyl diesel engines. This pin locks the flywheel in TDC position.

• Applications: BMW M54 | M57TU | M57T2 | M62 | M62VAN
• OEM Equiv: 11 5 180

This kit contains a special cap, and gauge in order to test oil pressure on a range of BMW engines.

• Engines: N20 | N46 | N55
• OEM equiv: 119250

This adaptor replaces the oil filter cap, and is used to test oil filter pressure.

• Applications: N20 (after 2012) | N46 | N55
• OEM equiv: 119 250 (119250)

This kit is designed for the removal & installation of camshaft / inlet camshaft & carrier assembly of the Valvetronic system. USE with ET1156B.

• Engine codes: N42 | N46
• Engines: 1.8L | 2.0L Twim Cam petrol

This kit is designed to disconnect the cam gear on New Generation 4 cylinder engines.

• Engine codes: N42 | N46

These specialised pliers are designed to remove the Valvetronic tension springs on BMW N42 | N46 engines. These pliers are essential for servicing the loaded spring clips on the rocker gear on the camshaft.

• Open the pliers carefully to unload the spring / close pliers to tighten the spring while installing it.

. This kit is specifically designed to facilitate the installation of stretch belts for BMW N52K (06-10) engines without causing damage, ensuring a secure and precise fit . In these engines, a separate stretch belt is used to drive the air conditioning pump.

• Suitable for use with BMW N52K engines, particularly in models such as the 2006-2013 BMW X5 3.0
• OEM Equiv: 11 1 240 (111240)

A specific timing tool kit for M3 / Z4 BMW vehicles fitted with the S50 / S54 (32 6S 4) chain driven 3.2L 6 Cyl 24V petrol engine.

• Applications: M3 S54 Cabriolet (00-06), Sports Coupe (99-06), CSL Sports Coupe (03-04)
• OEM Equiv: 11 2 300 | 11 5 100 | 11 7 160 | 11 7 342 | 11 9 130 | 119 140 | 11 9 170

A specialised mandrel for centering clutch discs on flywheels when installing self adjusting clutches (SAC). Designed to align the clutch disc before installing a self adjusting clutch.

Also suitable for aligning new / already pretensioned SAC clutches.

• 15mm diameter x 26.5mm x 80mm (overall length)
• Applications: 320i (E90 / N46), 325i (E90 / N52)
• Suits transmissions: GS6-17BG | GS6-17DG | S5D-250G

A specialised tool holds the driveshaft connecting nut. This is designed for use with the ET1653A.

• Engines: N20 | N52 | N54 | N55 | N57 | N63 | S63
• Series: F10 | F25

A specialised kit to facilitate timing chain replacement in BMW engines, offering major time savings.

A chain guide tool facilitates old chain withdrawal and simultaneous new chain insertion.

• Engine codes: N43 | N45 | N46 | N47
• Applications: E81 E87 E87 LCI E88 E82 F20 F20 LCI F21 F21 LCI E46 E90 E90 LCI E91 E91 LCI E92 E92 LCI E93 E93 LCI F30 F30 LCI F31 F35 F35 LCI E60 LCI E61 LCI F07 GT F07 GT LCI F10 F10 LCI F11 F11 LCI F06 GC F06 GC LCI F12 F12 LCI F13 F13 LCI X1 (E84) X3 (E83) X3 (E83LCI) X3 (F25) X4 (F26) X5 (E70LCI) X5 (F15) X6 (E71) X6 (F16) Z4 (E85) Z4 (E89) R56 R56 LCI R55 R55 LCI R57 R57 LCI R58 R59 R60 R61
• OEM Equiv: 83 30 2 354 985 (83302354985 )

Suits 2.5L | 3.0L Twin VANOS camshaft setting / locking on chain drive BMW VANOS 6 cylinder engines (98-). Due to the introduction of a Twin Vanos (variable valve control) system on the BMW 6 cyl twin cam chain driven petrol engine Vanos adjustment units fitted to inlet & exhaust camshafts must be reset to align with camshafts when setting engine timing after cam chain replacement. USE with ET1020A, ET1033A & ET1096

• Series: E36 (99-03) | E38 (90-02) | E39 (98-03) | E46 (08-07) | E53 (99-07) | E65 / E66 (02-05) | E85 / E86 (03-06)
• Engines: M52 | M54
• Engine codes: M52B20 | M52B25 | M54B25 | M52B28 | M54B30

This kit contains hydraulic rams, pads and tubes to remove upper sub frame caster bushings for aluminium arms. A 10 tonne hydraulic pump (not included) is recommended to be used with this kit.

• Applications: E31 | E32 (31 12 1 136 607), E34 (31 12 1 139 456), E38 | E39 (31 12 0 006 482), E53 (31 12 1 096 372), E65 | E66 (31 12 0 303 754)

This fitting allows for testing the VANOS adjusting unit. Designed to pressurise the single and double VANOS unit when checking or removing and installing.

• OEM Equiv: 11 3 450
• Engine codes: M50 | M52 | M54

VANOS electromagnetic (solenoid) valve socket. For 6 Cyl & 8 Cyl VANOS systems. Also suits Range Rover 4.4L V8 (03-05).

• Engine codes: M54 | M62
• 32mm deep socket

A specialised tool for removing / installing the transmission rubber mount bush on BMW X5 vehicles.

• Application: BMW X5 (E43 / 3.0L) before 2003
• Engine codes: M54B30 | M57D30

This puller can remove new style compact wheel bearing with or without locking C ring. This puller is adjustable so that it can fit most bearings. This puller is also able to be used as a hub puller.

• Applications: BMW E36 | E46 | E90, Mercedes W140 | W163 | W124 | W220, VW Touareg