Power Probe Gold Series Lead Set
SKU: ETPPLS01
The Gold Series Lead Set gives you the ability to extend your Power Probe circuit tester.
This kit includes 3 extension leads, 2 adaptors, two piercing probes and an extra probe tip. A must have kit for diagnosing electrical issues.
- Super flexible 10 gauge leads - stackable (1ft | 3ft | 6ft)
- Power Probe replacement tip
- Small piercing probe (Green) - for 20-28 gauge wires
- Large piercing probe (Yellow) - for 8-18 gauge wires
- 4mm female - female adaptor
- 4mm male - male adaptor
- Alligator clip adaptor
- Adaptor cap
Power Probe Wire Piercing Kit (2 Pce)
Very sharp probes suitable for piercing cable. Kit comes with two probes, one for 8-18 gauge wire, and the other for 20-28 gauge wire.
4mm banana jacks suit all standard multimeters / Power Probe units.
- Yellow - suits 8-18 gauge wire
- Green - suits 20-28 gauge wire
Power Probe 3" Probe Tip (2 Pack)
Replacement 3" probe tips, suitable for all Power Probe circuit testers. These are the original tips supplied with each Power Probe unit. For a longer 6" tip, refer PPTK0043.
- With 4mm banana jack
- Original part # PN3015-BLK
- 2 pack
Power Probe Alligator Clip
Banana jack alligator clip. This clips suits all Power Probe circuit testers.
- Original part # PN024
Power Probe Wire Extension | 3 Ft
A 3 foot wire extension for use with Power Probe circuit testers, plus most other diagnostic equipment which uses a standard 4mm banana plug.
- 3 foot wire extension
- 10 gauge multi strand wire
- 4mm banana plug connectors
- Stackable for versatility
- Original part # PNLS025-36RED
Power Probe Adaptor Set (2 Pce)
This Power Probe kit contains two adaptors - a male / male and a female / female adaptor. The 4mm connectors are suitable for use with all standard multimeters.
- male / male adaptor
- female / female adaptor
Power Probe Wire Extension | 1 Ft
A 1 foot wire extension for use with Power Probe circuit testers, plus most other diagnostic equipment which uses a standard 4mm banana plug.
- 1 foot wire extension
- 10 gauge multi strand wire
- 4mm banana plug connectors
- Stackable for versatility
Power Probe Wire Extension | 6 Ft
A 6 foot wire extension for use with Power Probe circuit testers, plus most other diagnostic equipment which uses a standard 4mm banana plug.
- 6 foot wire extension
- 10 gauge multi strand wire
- 4mm banana plug connectors
- Stackable for versatility
Power Probe Wire Piercing Kit (2 Pce)
Very sharp probes suitable for piercing cable. Kit comes with two probes, one for 8-18 gauge wire, and the other for 20-28 gauge wire.
4mm banana jacks suit all standard multimeters / Power Probe units.
- Yellow - suits 8-18 gauge wire
- Green - suits 20-28 gauge wire
Power Probe 3" Probe Tip (2 Pack)
Replacement 3" probe tips, suitable for all Power Probe circuit testers. These are the original tips supplied with each Power Probe unit. For a longer 6" tip, refer PPTK0043.
- With 4mm banana jack
- Original part # PN3015-BLK
- 2 pack
Power Probe Alligator Clip
Banana jack alligator clip. This clips suits all Power Probe circuit testers.
- Original part # PN024
Power Probe Wire Extension | 3 Ft
A 3 foot wire extension for use with Power Probe circuit testers, plus most other diagnostic equipment which uses a standard 4mm banana plug.
- 3 foot wire extension
- 10 gauge multi strand wire
- 4mm banana plug connectors
- Stackable for versatility
- Original part # PNLS025-36RED
Power Probe Adaptor Set (2 Pce)
This Power Probe kit contains two adaptors - a male / male and a female / female adaptor. The 4mm connectors are suitable for use with all standard multimeters.
- male / male adaptor
- female / female adaptor
Power Probe Wire Extension | 1 Ft
A 1 foot wire extension for use with Power Probe circuit testers, plus most other diagnostic equipment which uses a standard 4mm banana plug.
- 1 foot wire extension
- 10 gauge multi strand wire
- 4mm banana plug connectors
- Stackable for versatility
Power Probe Wire Extension | 6 Ft
A 6 foot wire extension for use with Power Probe circuit testers, plus most other diagnostic equipment which uses a standard 4mm banana plug.
- 6 foot wire extension
- 10 gauge multi strand wire
- 4mm banana plug connectors
- Stackable for versatility
| SKU | ETPPLS01 |
| Barcode # | 9321280322318 |
| Brand | Power Probe |
| Product weight | 0.9000kg |
| Shipping weight | 1.210000kg |
24 Months
Calculate Shipping
Flat Rate Shipping - $16.50
$16.50 flat rate shipping
Manual handling charge for long packaged products - $35.00
Manual handling charge for long packaged products
Others also bought
Power Probe 5V Tip Adaptor
Connects to any Power Probe circuit tester, limiting output voltage to 5V. Essential for safely testing sensors and computer circuits on vehicles.
Now you can supply a 5V reference signal to test computer modules, wiring and the components connected to them.
- Current limited 5V output
- Safely test computer sensor circuits
- Provides 5V reference voltage
- 12 - 24V input
- 5V output
- Standard 4mm banana connector
Power Probe Current Measuring Adaptor
An adaptor for measuring DC currents up to 20A (and as low as 1 milliamp). Displays current in realtime. This adaptor works with all Power Probe circuit testers!
- Measures up to 20A DC
- Measures as low as 1 milliamp
- Displays Min / Max
- Backlit LCD
Power Probe Parasitic Draw Monitor & Memory Sa
This product is designed for use in monitoring car battery voltage, leakage current, and serving as a backup power supply when replacing the battery. The product is connected to the car's OBDII interface via an OBDII connection cable to supply 12V power to the car and monitor the car system's leakage current for diagnosing various faults. It can also serve as a backup power supply for the car during battery replacement, preventing the car's mainboard from losing power and data. Draw Monitor can also monitor battery voltage through the OBDII port. Please read the instruction manual carefully before using the product.
- Supplies up to 10 amps
- Connects via OBDII
- View and record data via Bluetooth on App
- USB-C rechargeable
- Adjustable current output alarm & adjustable auto power off setting
- Graphing mode
- Monitor function input: 0-30V
- Voltage display accuracy: 1%+5dig resolution 0.1V
- Current display accuracy: 3%+5dig resolution 1mA
Power Probe True RMS Multimeter
The DM300AUTO is much more than a complete True RMS Digital Multimeter. It also includes several other functions of great utility for professionals in the automotive sector, such as checking the status of fuse protection, providing out of spec reading alerts, detecting parasitic draw, guiding automotive tests, checking the correct charging process of the alternator and measuring possible cranking voltages in the supply circuit.
The TFT colour display and the user friendly menu make this instrument an indispensable tool for automotive professionals.
- Measures current Flowing through fuses without removing the fuse (up to 80A)
- Fuse Voltage drop testing
- Guided automotive test such as Cranking Voltage / Alternator Charging
- AC/DC Voltage measurements up to 1000V
- Current measurements up to 30A
- Measures resistance, continuity and diode testing
- Frequency and duty cycle for PWM signals
More from this category
Power Probe 20 Ft Extension Cable
The Power Probe PPTK0029 is a 20-foot extension cable designed for use with the Power Probe 4 and Maestro diagnostic tools. It extends the reach of your Power Probe, making it ideal for testing electrical circuits on larger vehicles and trailers. This high-quality cable ensures consistent power delivery and secure connections for accurate diagnostics.
Power Probe 3 20 Ft Extension Cable
The Power Probe PPTK0027 is a 20 foot extension cable for use with Power Probe 3 and 3EZ diagnostic tools. It extends the reach of your Power Probe, making it ideal for testing electrical circuits on larger vehicles and trailers. This high-quality cable ensures consistent power delivery and secure connections for accurate diagnostics.
- 20 foot extension cable
- Original part # PN3049
Power Probe 3 Battery Clip Set
This clip set allows the Power Probe 3 circuit tester to be powered from any 12V source. Suits all Power Probe 3 models only.
- Original part # PN3046
Power Probe 3 Cigarette Adaptor
A Power Probe cigarette adaptor for use with Power Probe 3 | 3S | 3EZ. Allows the Power Probe circuit tester to be powered through the vehicle's cigarette port.
- Original part # PN3048
Power Probe 3" Probe Tip (2 Pack)
Replacement 3" probe tips, suitable for all Power Probe circuit testers. These are the original tips supplied with each Power Probe unit. For a longer 6" tip, refer PPTK0043.
- With 4mm banana jack
- Original part # PN3015-BLK
- 2 pack
Power Probe 5V Tip Adaptor
Connects to any Power Probe circuit tester, limiting output voltage to 5V. Essential for safely testing sensors and computer circuits on vehicles.
Now you can supply a 5V reference signal to test computer modules, wiring and the components connected to them.
- Current limited 5V output
- Safely test computer sensor circuits
- Provides 5V reference voltage
- 12 - 24V input
- 5V output
- Standard 4mm banana connector