SKU: T10-H-BIT50A

12V / 24V Battery Tester 12V / 24V Battery Tester

12V / 24V Battery Tester

Test battery charge / health for all 12V auto batteries and alternator / crank systems for 12V / 24V batteries, including new stop start batteries.

Print test results using the built in printer.

  • Tests all main battery standards
  • Max load voltage tests for 12V / 24V
  • Short circuit / reverse polarity protection

12V Battery System Monitor 12V Battery System Monitor

12V Battery System Monitor

Monitor battery status on all 12V automotive batteries. Wireless communication (up to 50m) by RF frequency. No need for cables / mobile phone app!

  • Solar powered with internal battery (or charge via USB)
  • Battery status (SOC / SOH / Voltage) etc. Plus check vehicle starting / charging systems.
  • Easy dashboard mount / audible alerts.

NEW
12V Brake & Clutch Pressure Bleeder 12V Brake & Clutch Pressure Bleeder

12V Brake & Clutch Pressure Bleeder

This pressure brake bleeder is designed to be portable, being powered by the vehicle's 12V battery. No shop air required!

Features adjustable output pressure up to a maximum 3.0 bar, with automatic cut-off function when pressure falls below 0.5 bar.

Supplied with premium quality adaptor set made from metal, not plastic.

  • Suitable for both hydraulic brake and clutch systems.
Bonus
ET4393-ADAP
12V Brake & Clutch Pressure Bleeder | Digital

12V Brake & Clutch Pressure Bleeder | Digital

Single handed brake bleeding. Powered by the vehicle's own battery. No shop air required!

  • Bleed pressure is closely controlled up to 3.0 bar - suitable for most vehicles (even those with ABS). Meets European OEM pressure requirements.
  • Auto shut off function when pressure falls below 0.5 bar.

12V Brake & Clutch Pressure Bleeder | Digital

12V Brake & Clutch Pressure Bleeder | Digital

Single handed brake bleeding. Powered by the vehicle's own battery. No shop air required!

  • Bleed pressure is closely controlled up to 3.0 bar - suitable for most vehicles (even those with ABS). Meets European OEM pressure requirements.
  • Auto shut off function when pressure falls below 0.5 bar.
  • Suitable for low viscosity brake fluids.
  • Supplied with European adaptor.

12V Lead Acid / Lithium Battery Analyser 12V Lead Acid / Lithium Battery Analyser

12V Lead Acid / Lithium Battery Analyser

A professional quality automotive battery tester for testing both 12V lithium ion and lead acid batteries. This tester uses conductance technology; a passive testing methodology which does not discharge / drain the battery. This analyser also checks the alternator's charging and starter's cranking condition.

  • Tests all 12V lithium ion / lead acid batteries for cars / motor cycles.
  • Print function via PC printer
  • Testing range: Lithium ion 20- 1000CCA | Lead acid 20 - 2000CCA

12V Motorcycle Battery Tester

12V Motorcycle Battery Tester

Advanced tester for 12V motorcycle batteries. Tests battery condition. Prints test reports via PC.

Simply enter the battery rating (printed on the battery) and test results are showing on the LCD screen.

  • Testing range: 20 - 300 CCA

12V OBD Memory Saver Cable

12V OBD Memory Saver Cable

Save vehicle memory when changing batteries. This avoids loss of radio and other similar vehicle settings. Simply connect cable to vehicle's OBDII port, and other end to a 12V power source.

  • EC5 connector for lithium jump packs
  • For 12V systems only

12V OBD Memory Saver Cable

12V OBD Memory Saver Cable

Save vehicle memory when changing batteries. This avoids loss of radio and other similar vehicle settings. Simply connect cable to vehicle's OBDII port, and other end to a 12V power source.

  • 2.5m cable
  • Alligator clips
  • For 12V systems only

12V OBDII Memory Saver Cable 12V OBDII Memory Saver Cable

12V OBDII Memory Saver Cable

Save vehicle memory when changing batteries. This avoids loss of radio and other similar vehicle settings. Simply connect cable to vehicle's OBDII port, and other end to a 12V power source.

  • LED light indicates when external power source is active
  • Fuse protects against current spikes

17T Hydraulic Injector Extractor Kit

17T Hydraulic Injector Extractor Kit

A specialised kit that assists with the extraction of very tight fitting injector nozzles, utilising a special pull spindle.

Contains a 17T hydraulic ram, with 15mm stroke. Height retracted 89mm | extended 104mm

  • M14 x 1.5 pitch Pulling Spindle 240mm long.
  • M14 x 1.5 pitch Pulling Spindle 315mm long.
  • M17 x 1.0 pitch Pulling Spindle 240mm long.
  • M17 x 1.0 pitch Pulling Spindle 315mm long.
  • M18 x 1.5 pitch Pulling Spindle 315mm long.
  • M25 x 1.0 pitch Pulling Spindle 240mm long.

3 Leg Self Gripping Gear Puller

3 Leg Self Gripping Gear Puller

  • SPREAD: 80mm
  • REACH: 90mm
  • CAPACITY: 1.1 tonnes

3 Leg Self Gripping Gear Puller | 150mm

3 Leg Self Gripping Gear Puller | 150mm

A special self gripping puller with slim legs. Able to be used with a slide hammer.

  • Spread: 150mm
  • Reach: 150mm
  • Capacity: 1.1 tonnes

3 Leg Self Gripping Gear Puller | 200mm

3 Leg Self Gripping Gear Puller | 200mm

A special self gripping puller with slim legs. Able to be used with a slide hammer.

  • Spread: 15 - 200mm
  • Reach: 200mm
  • Capacity: 1.17 tonnes

3 Point Impact Socket

3 Point Impact Socket

8TS

SKU: ET1223E

3 Point Impact Socket

Three point impact socket for general repairs on Nissan vehicles, especially the transmission pump and balance shaft fixings.

  • Size: 8TS
  • Length: 38mm
  • Drive: 1/2" Sq Drive
  • Chrome Moly

3/4" Sq Drv Ratcheting Head

3/4" Sq Drv Ratcheting Head

Simply convert your standard 3/4" flexible breaker bar, into a ratcheting breaker bar. This ratcheting head just goes on the end of any standard 3/4" Sq Drv breaker bar.

4 Pin Lock Nut Socket Set (Internal Teeth)

4 Pin Lock Nut Socket Set (Internal Teeth)

A specialised set of 4 pin lock nut sockets for driving lug lock nuts with external teeth. The kit contains sockets from 20mm - 72mm diameter.

Please refer to the kit components for details of individual sockets.

  • 1/2" Sq Drv
  • 60mm overall length

4 Way TPMS Valve Tool 4 Way TPMS Valve Tool

4 Way TPMS Valve Tool

SKU: ET6037

4 Way TPMS Valve Tool

A handy tool for removing and replacing the 11mm and 12mm TPMS sensor nuts and reseating the bevelled and non bevelled sensor grommets.

  • 4 way design
  • 11mm | 12mm TPMS sensor nuts

4-in-1 Wheel Nut Socket

4-in-1 Wheel Nut Socket

An essential glovebox / toolbox addition! One socket drives 4 common wheel nut sizes - saving both space and weight. Impact grade for use with both hand / impact tools.

Supplied with bonus extension bar.

  • 6 point (single hex)
  • Sizes: 17 | 19 | 21 |22mm
  • 1/2" Sq Drv
  • Impact grade

A/C & Fuel Line Disconnect Set

A/C & Fuel Line Disconnect Set

For press type disconnection clips on Chrysler, Ford, Holden etc.

  • Fuel line: 5/16” & 3/8”
  • Air con: 3/8” | 1/2" | 5/8 ” | 3/4"

A/C Clutch Hub Puller Kit

A/C Clutch Hub Puller Kit

This kit contains a wide range of air conditioning clutch hub pullers / installers for Ford, Holden, Chrysler and a range of other vehicles.

Included in this kit are forcing screws, removing flange, and adaptor assembly to install / remove most clutch hubs.

  • Applications: Holden-Harrison DA-6, HR-6 and V5, A-6 and early R4 | Nippon Denso Ford / Chrysler A590, C171 & FS-6 | New Style, Sanden, York / Tecumesh HR980 | Zetex / Mitsubishi CH Series

A/C Compressor Belt Installer

A/C Compressor Belt Installer

Essential tool for A/C belt installation on Mazda 3 / Mazda 6 / Ford Focus.

A/C Compressor Seal & Bearing Service Kit

A/C Compressor Seal & Bearing Service Kit

A comprehensive kit for replacing air conditioning seals, clutches and clutch bearings. This kit suits Diesek Kiki (Zexel) | Hitachi | Mitsubishi | Nippondenso | Seiko-Seiki | Sanden.

ABS Sensors Reamer Kit ABS Sensors Reamer Kit

ABS Sensors Reamer Kit

A specialised kit for removing dust / dirt / rust when reseating ABS sensors. The kit contains 5 reamers, and one drill to suit most European vehilces.

Designed for use with a 1/4" drv flexible ratchet handle (not included).

  • M10 x 133mm | VAG, Holden
  • M14 x 42.5mm | BMW
  • M15 x 33.5mm | Mercedes, Mazda, Toyota, Ford
  • M18 x 31.5mm | VAG, BMW (E36 | E46)
  • M18 x 42.5mm | VAG, NFZ
  • M8 x 180mm Drill | VW T5

ABS Wheel Speed Sensor Reamer ABS Wheel Speed Sensor Reamer

ABS Wheel Speed Sensor Reamer

A specialised reamer for ABS wheel speed sensors. The fixture hole should be thoroughly cleaned before replacing the sensor.

This 11mm reamer enables precise cleaning of the fixture hole, without expanding the hole diameter / damaging the sensor wheel.

  • 11mm diameter reamer
  • Applications: VAG, including Golf Gen 6 / 7, Audi A3, Skoda Octavia, SEAT Leon

Actros Axle Bolt Socket | Torx Plus EPL #32

Actros Axle Bolt Socket | Torx Plus EPL #32

  • Torx Plus EPL #32
  • 90mm overall length
  • Chrome Moly construction

Actros Axle Bolt Socket | Torx Plus EPL #32

Actros Axle Bolt Socket | Torx Plus EPL #32

  • Torx Plus EPL #32
  • 50mm overall length
  • Chrome Moly construction

Adaptor | Ford Ranger | 41mm

Adaptor | Ford Ranger | 41mm

SKU: ETWH500BC-48

Adaptor | Ford Ranger | 41mm

This brake bleeder adaptor has been designed to allow pressure brake bleeding on the Ford Ranger from 2012 onwards. This cap screws directly onto the master brake cylinder.

  • Suits Ford Ranger (2012 onwards) vehicles.
  • Nitto style connector fitting
  • Zinc alloy construction
  • 41mm diameter

Adaptor Colorado | Isuzu D-Max (54mm)

Adaptor Colorado | Isuzu D-Max (54mm)

An individual master cylinder adaptor for use with standard pressure brake bleeders, including the ETWH505H. This adaptor is designed to connect to the master cylinder reservoir to allow replacement brake fluid to be pushed through the system.This adaptor suits Colorado / Isuzu D-Max vehicles.

  • Suits Colorado / Isuzu D-Max vehicles.
  • Nitto style connector fitting
  • Zinc alloy construction
  • 54mm diameter

Adaptor Honda | 55mm

Adaptor Honda | 55mm

SKU: ETWH500BC-26

Adaptor Honda | 55mm

An individual master cylinder adaptor for use with standard pressure brake bleeders, including the ETWH505H. This adaptor is designed to connect to the master cylinder reservoir to allow replacement brake fluid to be pushed through the system.This adaptor suits Honda vehicles.

  • Suits Honda vehicles.
  • Nitto style connector fitting
  • Zinc alloy construction
  • 55mm dia

Adaptor Honda | 74mm

Adaptor Honda | 74mm

SKU: ETWH500BC-25

Adaptor Honda | 74mm

An individual master cylinder adaptor for use with standard pressure brake bleeders, including the ETWH505H. This adaptor is designed to connect to the master cylinder reservoir to allow replacement brake fluid to be pushed through the system.This adaptor suits Honda vehicles.

  • Suits Honda vehicles.
  • Nitto style connector fitting
  • Zinc alloy construction
  • 74mm dia

Adaptor Mitsubishi | 34mm

Adaptor Mitsubishi | 34mm

SKU: ETWH500BC-23

Adaptor Mitsubishi | 34mm

An individual master cylinder adaptor for use with standard pressure brake bleeders, including the ETWH505H. This adaptor is designed to connect to the master cylinder reservoir to allow replacement brake fluid to be pushed through the system.This adaptor suits Mitsubishi vehicles.

  • Suits Mitsubishi vehicles.
  • Nitto style connector fitting
  • Zinc alloy construction
  • 34 mm dia

Adaptor Mitsubishi | 35.5mm

Adaptor Mitsubishi | 35.5mm

SKU: ETWH500BC-22

Adaptor Mitsubishi | 35.5mm

An individual master cylinder adaptor for use with standard pressure brake bleeders, including the ETWH505H. This adaptor is designed to connect to the master cylinder reservoir to allow replacement brake fluid to be pushed through the system.This adaptor suits Mitsubishi vehicles.

  • Suits Mitsubishi vehicles.
  • Nitto style connector fitting
  • Zinc alloy construction
  • 35.5mm dia

Adaptor Toyota | 23mm

Adaptor Toyota | 23mm

SKU: ETWH500BC-24

Adaptor Toyota | 23mm

An individual master cylinder adaptor for use with standard pressure brake bleeders, including the ETWH505H. This adaptor is designed to connect to the master cylinder reservoir to allow replacement brake fluid to be pushed through the system.This adaptor suits Toyota vehicles.

  • Suits Toyota vehicles.
  • Nitto style connector fitting
  • Zinc alloy construction
  • 23mm dia

Adaptor Toyota | Lexus

Adaptor Toyota | Lexus

43mm Dia

SKU: ETWH500BC-21

Adaptor Toyota | Lexus

A specialised brake bleeder adaptor, for pressure style brake bleeders. Suits a range of Toyota / Lexus vehicles. Part of the Endeavour Range of brake bleeder tools.

  • Suits Toyota / Lexus vehicles.
  • Nitto style connector fitting
  • 43mm dia

AdBlue Filter Socket

AdBlue Filter Socket

This socket is specifically designed for AdBlue filters on Mercedes vehicles with BlueTec engines. AdBlue additives reduce NOx emissions in some passenger / light commercial models.

  • 46mm diameter
  • Single hex impact socket
  • 3/8" Sq Drv

Adjustable Camshaft Pulley Holding Tool

Adjustable Camshaft Pulley Holding Tool

A versatile tool for holding the camshaft gear when loosening / tightening the centre bolt. The adjustable jaw and replaceable pin sets makes this kit universal in application.

  • This kit has been updated with two extra pin sets. These 5mm / 8mm pins are essential to suit late model VAG engines.

Adjustable Crankshaft Pulley Holding Tool

Adjustable Crankshaft Pulley Holding Tool

Interchangeable grooved pins hold crankshaft pulley stationary when loosening / tightening the centre bolt. Includes 3 interchangeable pairs of pins - 6mm diameter. Pin lengths: 70mm, 74mm, 110mm.

  • Applications include Mercedes (M112 | M113 | M271 | M642) and Nissan (A32 | A33)
  • Adjustable range: 30 - 50mm PCD
  • Overall length: 15-1/4" (388mm)

Adjustable Fuel Tank Wrench

Adjustable Fuel Tank Wrench

Adjustable jaws make this fuel tank locking ring remover applicable to a range of vehicles. Simply loosen the lock nuts on the tool, and adjust so that the slots fits over the teeth in the plastic ring on the fuel tank.

  • Adjustable 56 - 189mm range
  • Civic | Corolla + many other models
  • Use with 3/8" wrench